manualshive.com logo in svg

Nimbra 300 Series, Руководство по установке и обслуживанию

Поделиться
Скачать
Nimbra 300 Series Скачать руководство пользователя страница 32

30  

•

  Contents

Installation and Maintenance Manual Nimbra 300 Series

©2006 Net Insight AB, All rights reserved

Transceiver Modules

Introduction

Small Form-factor Pluggable (SFP) transceiver modules provide a flexible and
reliable optical interface  for  a variety of interface rates and ranges. The SFP
module consists of an optical subassembly housing both the optical transmitter
and the optical receiver functions, and an electrical subassembly. All are
packaged together with a top metal cover and bottom shield that plugs into a
circuit board in accordance with the standard Multisource Agreement (MSA).

The optical subassembly consists of two parts. The transmitter side is equipped
with an electrical driver circuit and a high-performance light source, typically a
laser diode or sometimes an LED for multimode fiber and lower bit rates. The
receiver side has a photo detector, either a PIN diode or an APD depending on
performance requirements, and an electrical amplifier. Optical fibers are
connected with a duplex LC connector.

Inventory data for each SFP are available in the Nimbra element management
system. Most modules also provide digital diagnostic outputs including
parameters such as temperature, transmit power, receive power, and laser bias
current.

SFPs offer a reliable and convenient way of interfacing PCBs to optical fiber
cable. There are a number of advantages of pluggable modules over conventional
fixed optical transmitters and receivers:

Note:

All Net Insight SFP modules have been thoroughly tested individually
as  well  as  on  the  Nimbra  platform  to  guarantee  system  performance.
Use  of  Net  Insight’s  SFP  is  a  prerequisite  for  the  stated  functionality
and performance of the Nimbra platform, and no obligation, warranty
or  liability  for  system  performance  is  offered  for  use  of  the  Nimbra
system with SFP modules purchased from third parties.

These SFP modules are used for bit rates ranging from 155 Mbps to 2488 Mbps.

SFPs for OC-3/STM-1 ports

OC-3/STM-1 SFPs with different ranges.

Product number

SONET/SDH
Interface type

Wavelength

Fiber type

Range

NPA0016-LS11

Not Applicable

1310nm

Multimode

2km

NPA0016-LJ11

IR-1/S-1.1

1310nm

Singlemode

15km

NPA0016-LL11

LR-1/L-1.1

1310nm

Singlemode

40km

NPA0016-VL21

LR-2 /L-1.2

1550nm

Singlemode

80km

SFP with electrical interface.

Product number

SONET/SDH
Interface type

Media type

Connector

Range

NPA0011-1551

ITU-T G.703

75ohm
coaxial

1.0/2.3

100m

Содержание 300 Series




















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды