Ness D16XCEL Скачать руководство пользователя страница 56 | Manualshive

Страница: 56 / 96

background image

Option No.

Description

Default

P89E

1E

ENABLE TEST CALLS

ON

2E

Mains Report Delay (1 hour)

ON

3E

[not used]

OFF

4E

Swinger shutdown

ON

5E

Line Fault Monitor

OFF

6E

Master Code Clears Dial Attempts

OFF

7E

[not used]

OFF

8E

[not used]

OFF

P89E 1E

EnAbLE tEst CALLs

ProgrAm moDE LEVEL

Installer

FACtory DEFAULt

ON: Test Calls enabled.

rELAtED oPtions

P83E Test Call Interval.

P84E Time before next Test call.

P87E 4E Number Of Dialling Attempts.

notEs

Test Calls cannot be sent by SMS, only

to a central station.

Enables the reporting of dialler test calls to the Central station.

KPX+

P89E 1E to enable/disable the option

NAVIGATOR

P89E > enable/disable 1E

SMS*

P[MasterCode]E P[InstallerCode]E P89E 1E

Or use

NessXCEL

app

P89E 2E

mAins rEPort DELAy

ProgrAm moDE LEVEL

Installer

FACtory DEFAULt

ON: Mains Fail report is delayed.

Allows Mains Fail reports to be delayed by one hour if the mains power has been off
continuously for that time. This avoids mains fail reports being sent to the Central Station
in the event of brief power failures.

KPX+

P89E 2E to enable/disable the option

NAVIGATOR

P89E > enable/disable 2E

SMS*

P[MasterCode]E P[InstallerCode]E P89E 2E

Or use

NessXCEL

app

P89E 4E

sWingEr shUtDoWn

ProgrAm moDE LEVEL

Installer

FACtory DEFAULt

ON: Swinger Shutdown enabled.

notEs

This prevents unnecessary multiple

alarms reported to the Central station

in cases, for example, where a door is

‘swinging’ in the wind.

This option only applies to zones

enabled to Report Multiple Zone

Alarms.

rELAtED oPtions

P78E Report Multiple Zone Alarms.

Limits the number of calls made by a zone alarm in any one armed period. Alarm reports
are normally limited to 15 multiple reports per zone. When Swinger Shutdown is enabled,
multiple reports are reduced to 3 multiple reports per zone.

KPX+

P89E 4E to enable/disable the option

NAVIGATOR

P89E > enable/disable 4E

SMS*

P[MasterCode]E P[InstallerCode]E P89E 4E

Or use

NessXCEL

app

* SMS programming shows the full SMS string to send. KPX+ and

NAVIGATOR programming assumes the panel is already in program mode.

56

NESS D8XCEL / D16XCEL CONTROL PANEL – INSTALLATION MANUAL REV 1.1

P r o g r A m m i n g

«
...
54
55
56
57
58
...
»

Содержание D16XCEL

































































































Отзывы:

Нет отзывов

Похожие инструкции для D16XCEL

Бренд: UNITED Страницы: 8

Бренд: Salda Страницы: 16

Бренд: Federal Signal Corporation Страницы: 60

Бренд: FASTRON. Страницы: 16

NOVASTAT EL DIGITAL

Бренд: Taconova Страницы: 7

Бренд: DeLaval Страницы: 102

Бренд: Roger Страницы: 21

Бренд: Seneca Страницы: 4

Бренд: Delabie Страницы: 20

Бренд: Linear Technology Страницы: 32

Бренд: Rain Bird Страницы: 48

Бренд: Sullair Страницы: 31

Бренд: EOS Страницы: 7

Бренд: Water Specialist Страницы: 36

Бренд: DirectConnect Страницы: 2

CS ME-02 Series

Бренд: pizzato Страницы: 12

Бренд: Water Specialist Страницы: 60

Бренд: aerl Страницы: 27

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды