Neomatica ADM700 3G Скачать руководство пользователя страница 71

Страница: 71 / 80

Neomatica, LLC. Terminal ADM700 3G GLONASS/GPS. Ed. 7.2, dd. 24.11.2018

12 Tracker software upgrading

Tracker software upgrade (firmware) can be performed through the USB-interface by means

of configuration program or via GPRS-channel.

12.1 Tracker software upgrading via USB

If the computer is connected to the Internet network then the configuration program checks the

valid firmware version in the upgrade server and if necessary, downloads the firmware file.

To upgrade firmware, do the following:

⎯

after having switched off the external power, connect USB cable (miniUSB/USB-A) to the

tracker and Personal computer USB port;

⎯

supply the power to the tracker from the vehicle circuit or a laboratory power source;

⎯

launch “ADMConfigurator” program on personal computer;

⎯

if a more recent firmware version than the one installed on the tracker is detected,

“ADMConfigurator” program will inform you of its presence;

⎯

press “Upgrade available”;

⎯

in the opened tab “Notifications” press “firmware upgrade via USB”;

⎯

after being upgraded, the tracker will be rebooted and become available for work.

WARNING!

Don't switch the tracker power off when upgrading the tracker firmware until the

tracker is detected by the setting program. Otherwise there is a risk of damaging the software

which recovery can be performed only in the manufacturer's office.

12.2 Tracker software upgrading via USB with a firmware file

Firmware file should be requested in technical support.

To upgrade the firmware via the USB interface with a firmware file, do the following:

⎯

after having switched off the external power, connect USB cable (miniUSB/USB-A) to the

tracker and Personal computer USB port;

⎯

supply the power to the tracker from the vehicle circuit or a laboratory power source;

⎯

launch “ADMConfigurator” program on personal computer;

⎯

after having connected the terminal to the progr

am, open the “Settings” section in the

“Device” tab, press “Flash the file”;

⎯

press “Yes” in the popup;

⎯

drag the firmware file in the respective field in the

сonfigurator window;

⎯

after the firmware is upgraded, the tracker will be rebooted and become available for work.

Содержание ADM700 3G

















































































Результаты поиска

Содержание ADM700 3G

Отзывы:

Похожие инструкции для ADM700 3G

Бренды по названию

Популярные бренды

Neomatica ADM700 3G, Руководство по эксплуатации

Результаты поиска

Содержание ADM700 3G

Отзывы:

Похожие инструкции для ADM700 3G

Бренды по названию

Популярные бренды