Neomatica ADM700 3G Скачать руководство пользователя страница 12

Страница: 12 / 80

Neomatica, LLC. Terminal ADM700 3G GLONASS/GPS. Ed. 7.2, dd. 24.11.2018

4. Tracker operation rules

Tracker installation should be performed by persons familiarized with operation principles,

item design and this Operation Manual. When using the tracker, the staff should follow the

recommendations according to safety precautions applied while working with consumers' power

units.

It is forbidden:

−

to use the tracker in any conditions different from those described in relation to the tracker

technical features.

−

to use tracker with damage and/or liquid penetration signs.

−

to open the tracker case when it is under voltage as well as to open its case by someone

who does not have necessary qualification, did not familiarize with operation principles, item

design and this Operation Manual.

−

to clean the tracker with any aggressive liquids, solvents, chemical or abrasive agents

capable to harm its case, energy-supply elements, fixing system or disturb proper function of the

tracker in any way. For cleaning it is necessary to use a clean dry cotton tissue or a soft brush.

−

Intentionally bring the tracker into condition not previewed by this Operation manual,

technical requirements or other documents describing the tracker operation.

−

to use the tracker in cases, which may cause its damage, harm its energy-supply systems,

affect staff's health or use it in any other way causing dangerous situations and financial losses.

After trackers transportation in sub-zero temperatures they should be stored at room

temperature within 24 hours.

5 Installation procedure

The internal GLONASS/GPS and GSM antennas are used in the tracker, which allow for its

installation almost in any place of the vehicle. However, it is not recommended to install it in the

places where the received signals will be attenuated by the vehicle metallic housing, since this

may affect the tracker operation quality.

Before installation, it is necessary to install a SIM-card with activated data transmission

service via GPRS, SMS and sufficient balance for these services. Then the power is supplied to

the MF-24F connector wires: the plug contact 12 is connected to the positive voltage of the

vehicle electrical system, the plug contact 24

– to the negative voltage of the vehicle electrical

system (housing, GND). Contacts arrangement layout for MF-24 connector is provided in the

Figure 2. It is necessary to install a 2A melting fuse between the positive ground of the vehicle

Содержание ADM700 3G

















































































Результаты поиска

Содержание ADM700 3G

Отзывы:

Похожие инструкции для ADM700 3G

Бренды по названию

Популярные бренды

Neomatica ADM700 3G, Руководство по эксплуатации

Результаты поиска

Содержание ADM700 3G

Отзывы:

Похожие инструкции для ADM700 3G

Бренды по названию

Популярные бренды