NEC V850E/PH2 Скачать руководство пользователя | Manualshive

Страница: 398 / 1053

background image

398

Chapter 10

16-bit Inverter Timer/Counter R

User’s Manual U16580EE3V1UD00

10.10.4 One-shot pulse mode

(1)

Outline of one-shot pulse mode

When, in the one-shot pulse mode, the duty is set to the TRnCCR0 register, the output duty delay
value is set to the TRnCCR1 to TRnCCR5 registers, and bit TRnCE of the TRnCTL0 register is set
to 1, external trigger input (

TTRGR1 pin of TMR1

) wait results, with the counter remaining stopped

at FFFFH. Upon detection of the valid edge of external trigger input (

TTRGR1 pin of TMR1

), or

when bit TRnEST of the TRnCTL0 register is set to 1, count up starts. The TORn1 to TORn5 pins
become high level upon a match between the counter and TRnCCR1 to TRnCCR5 registers.
Moreover, upon a match between the counter and TRnCCR0 register, the TORn1 to TORn5 pins
become low level, and the counter is cleared to 0000H and then stops. The TORn0 pin performs
toggle output during the count operation upon a match between the counter and the TRnCCR0
buffer register. Moreover, upon a match between the counter and TRnCCR0 register during count
operation, a compare match interrupt (INTTRnCC0) is output, and upon a match between the
counter and TRnCCR1 to TRnCCR5 buffer registers, compare match interrupts (INTTRnCC1 to
INTTRnCCR5) are output.
The TRnCCR0 and TRnCCR1 registers can be rewritten using the anytime write method,
regardless of the value of bit TRnCE.
Even a trigger is input during the counter operation, it is ignored. Be sure to input the second
trigger when the counter is stopped at 0000H.
In the one-shot pulse mode, registers TRnCCR0 to TRnCCR3 have their function fixed as
compare registers, so the capture function cannot be used.

[One-shot pulse operation flow]

<1> TRnCTL1 register bits TRnMD3 to TRnMD0 = 0011B (One-shot pulse mode)
<2> TRnCCR0 register setting (duty setting), TRnIOC0 register bit TRnOE1 = 1

(TORn1 pin output enable)

<3> TRnCTL0 register bit TRnCE = 1 (counter operation enable):TORn1 = Low-level output
<4> TRnCTL1 register bit TRnEST = 1 or TTRGR1 pin edge detection

of TMR1

(count-up start):

TORn1 = Low-level output

<5> Match between counter value and TRnCCR1 buffer register: TORn1 = High-level output
<6> Match between counter value and TRnCCR0 buffer register:TORn1 = Low-level output,

count clear

<7>  Count stop: TORn1 = Low-level output
<8>  TRnCE = 0 (operation reset)
<9>  <1> to <2> can be in any order.

Caution:

In the one-shot pulse mode, set bit TRnEEE of the TRnCTL1 register to 0.

«
...
396
397
398
399
400
...
»

Содержание V850E/PH2






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для V850E/PH2

Бренд: iCeeO2 Страницы: 7

Бренд: Canarm Страницы: 3

Бренд: J3C Страницы: 2

Бренд: Netro Страницы: 14

Бренд: HANYOUNG NUX Страницы: 4

ISaGRAF WinCE ViewPAC

Бренд: ICP DAS USA Страницы: 192

Бренд: Midian Electronics Страницы: 22

Sigma II Series

Бренд: YASKAWA Страницы: 359

NetGuardian LPG D-PK-NGLPG

Бренд: DPS Telecom Страницы: 82

Thermo Call TC3

Бренд: Webasto Страницы: 15

Hauser COMPAX-M Series

Бренд: Parker Страницы: 84

Бренд: Danfoss Страницы: 44

Бренд: Work Pro Страницы: 9

Бренд: Zaber Страницы: 23

Бренд: NXP Semiconductors Страницы: 11

Бренд: Bornay Страницы: 66

Бренд: Niko Страницы: 40

Бренд: Sierra Wireless Страницы: 58

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды