1093
Single Line Telephones
Description
The system is compatible with Dial Pulse and DTMF analog single line telephones (SLTs). You can
install single line telephones as On-Premise or Off-Premise extensions. Single line telephone users
can dial codes to access many of the features available to multiline terminal users. With single line
telephones, you can have your system simulate PBX operation.
When installing single line telephones you must have:
A port on an LCF blade for each single line telephone installed.
If you have DTMF sets, at least one block reserved on the GCD-CP10 for analog extension
DTMF reception.
DTMF Dial Out Timer Added
A program is added for DTMF dialing, Program 20-03-07 : System Options for Single Line
Telephones
-
Trunk Call Dial Forced Sending Start Time (Forced Dial). When Program 20-03-03 :
System Options for Single Line Telephones
– SLT DTMF Dial to Trunk Lines is set to 0 (receive all digits
before sending), the system follows the timer in Program 20-03-04 and Program 20-03-07.
The timer in Program 20-03-04 System Options for Single Line Telephones
– Dial Sending Start Time
for SLT or ARS resets when the user dials another digit.
The timer in Program 20-03-07 System Options for Single Line Telephones
– Trunk Call Dial Forced
Sending Start Time (Forced Dial) does not reset when a digit is dialed. The user must finish dialing all the
digits before this time expires (entries: 0~64800 seconds, default: 0).
Conditions
Dial Pulse single line telephones cannot access any feature that requires the user to
dial
#
or
*
.
A single line telephone can initiate an Internal Zone page, but cannot receive an Internal
Zone Page.
When a Ring Group call rings a single line station, the BLF indication shows busy.
Stutter Dial Tone is supported to Single Line Telephones for Voice Mail Message Waiting.
The GCD-CP10 has 32 resources for DTMF receiving and Dial Tone detection. When a
GPZ-BS10 is installed there are 64 resources available.
When Program 10-09-01 is set to 0 (Common) and Program 14-02-10 (Caller ID) is set to 1
(Yes), all DTMF/Dial Tone Detection resources are always allocated to analog trunks, not
analog extensions. However, if Program 14-02-10 (Caller ID) is set to 0 (No), all DTMF/Dial
Tone Detection resources can be used for both analog trunks and analog extensions.
The Exclusive Hold Recall Timer is used when an internal call from a Single Line Telephone
is placed on hold.
A maximum of two single line telephones can be connected, in series, on one port as long
as the maxim cable resistance stays below 600 Ohms.
Содержание Univerge SV9100
