NEC Express5800/E120f-M Скачать руководство пользователя

Страница: 40 / 165

5. Troubleshooting

Express5800/E120f-M Maintenance Guide

Chapter 1 Maintenance

5.8

When OS is in Operation

[?]

Windows operation is unstable



Have you installed the Starter Pack?

→

If the network driver is installed after OS is installed, Windows operation may become unstable. Install

the Starter Pack by referring to the description about how to install the Starter Pack for each OS in
"

Installation Guide (Windows)

[?]

After the system is restored from the backup tool, Windows is misbehaving

→

Install the Starter Pack by using EXPRESSBUILDER (refer to

Installing Starter Pack

in "

Installation

Guide (Windows)

[?]

Fails to be recognized on network



Is the cable connected properly?

→

Securely connect the proper cable to the network port on the rear of the server. Additionally, make sure

that the cable conforms to the network interface standards.



Are BIOS settings correct?

→

You can disable the internal network controller using the BIOS setup utility. Check the settings with

BIOS setup utility.



Have you completed protocol and services settings?

→

Verity that the network driver for the server network controller has been installed. Also verify that

protocol such as TCP/IP or various services have been properly specified.



Are transfer rate settings correct?

→

Verify that the transfer rate and duplex mode are the same as those of the connecting hubs.

[?]

There are RX dropped packets when the system was started on Linux

→

Although there may be RX dropped packets when the system is started, there is no operational problem.

Check the system and network environment when there are RX dropped packets during operation or
when there is no communication.

Содержание Express5800/E120f-M






































































































































































Результаты поиска

Содержание Express5800/E120f-M

Отзывы:

Похожие инструкции для Express5800/E120f-M

Бренды по названию

Популярные бренды

NEC Express5800/E120f-M, Руководство по обслуживанию

Результаты поиска

Содержание Express5800/E120f-M

Отзывы:

Похожие инструкции для Express5800/E120f-M

Бренды по названию

Популярные бренды