NEC Express5800/E120f-M Скачать руководство пользователя страница 139

Страница: 139 / 165

1. POST Error Message

Express5800/E120f-M Maintenance Guide

139

Chapter 3 Appendix

Error Message

Cause

Solution

C300

Out-of-band setup

configuration failure

Configuration change requested by

remote terminal via network failed.

Unplug the power cord, wait for at least 30

seconds, then restart the server. If the

same error is detected repeatedly, contact

your sales representative.

C301

SDR mismatch error

Inconsistency in the hardware

information of the sensor data record

was detected

Contact your sales representative.

C302

Hardware configuration

error.

Illegal hardware configuration was

detected.

C303

FAN Structure ID command

error.

Illegal fan control was detected when

RAID Controller is installed.

C304

Necessary to update SDR

Version for new RAID Card.

SDR for RAID Controller is

inappropriate.

C320 Unmatched PSUs.

Unmatched power supply units are

configured.

C321 System power consumption is

out-of-range in PSUs.

System power consumption exceeds

the power output capacity limit.

C322 No information for system

power consumption check.

No information is acquired in checking

system power consumption.

C324

Unsupported combination of
module enclosure and server
module.

Unsupported combination of module

enclosure and server module.

The server may fail to operate correctly.

Contact your sales representative.

C325

Can't read module enclosure
FRU.

Cannot read module enclosure FRU. The chassis information may be lost, or

module is failed. Contact your sales

representative.

C501 Intel(R) Node Manager is in

Recovery Mode.

Intel Node Manager is in Recovery

Mode.

Unplug the power cord, wait for at least 30

seconds, then restart the server. At that

time, check the jumper switch setting on

motherboard. If the same error is detected

repeatedly, contact your sales

representative.

Содержание Express5800/E120f-M






































































































































































Результаты поиска

Содержание Express5800/E120f-M

Отзывы:

Бренды по названию

Популярные бренды

NEC Express5800/E120f-M, Руководство по обслуживанию

Результаты поиска

Содержание Express5800/E120f-M

Отзывы:

Бренды по названию

Популярные бренды