NEC Express5800/E120f-M Скачать руководство пользователя

Страница: 138 / 165

1. POST Error Message

Express5800/E120f-M Maintenance Guide

138

Chapter 3 Appendix

Error Message

Cause

Solution

C10B

BMC operational code
corrupted.

Failed to start BMC firmware.

Unplug the power cord, wait for at least 30

seconds, then restart the server. If the

same error is detected repeatedly, contact

your sales representative.

C10C

BMC update firmware

corrupted.

An illegality was detected while

updating BMC firmware.

C10D

Internal Use Area of BMC FRU

corrupted.

An illegality was detected in FRU

containing the device information.

C10E

BMC SDR Repository empty.

An error was detected on BMC SDR.

C10F

IPMB signal lines do not

respond.

Failure of Satellite Management

Controller was detected.

C110

BMC FRU device failure.

An error was detected in FRU that

contains device information.

C111

BMC SDR Repository failure.

Failure was detected in SROM that

stores the SDR.

C112

BMC SEL device failure.

Device failure was detected in BMC

SEL.

C113

BMC RAM test error.

An error was detected in BMC RAM.

C114

BMC Fatal hardware error.

A hardware error was detected in

BMC.

C115

Management controller

not responding

Management controller does not

respond.

Update the BMC firmware.

If the same error is detected repeatedly,

contact your sales representative.

C116

Private I2C bus not

responding.

Private I2C bus does not respond.

Unplug the power cord, wait for at least 30

seconds, then restart the server. If the

same error is detected repeatedly, contact

your sales representative.

C117

BMC internal exception

BMC internal error was detected.

C118

BMC A/D timeout error.

BMC A/D timeout error was detected.

C119

SDR repository corrupt.

BMC error or illegal SDR data was

detected.

C11A

SEL corrupt.

BMC error or illegal system event log

data was detected.

C11B

BMC Mezzanine card is not

found.

BMC Mezzanine card is not installed. Contact your sales representative.

C11C

BMC Mezzanine partition is

invalid.

A format error was detected in BMC

Mezzanine card.

C11D

BMC is in Forced Boot Mode.

Detected that BMC is in Forced Boot

Mode.

Unplug the power cord, wait for at least 30

seconds, then restart the server. At that

time, check the jumper switch setting on

motherboard. If the same error is detected

repeatedly, contact your sales

representative.

C11E

Communication with BMC was

failed in previous boot

Communication with BMC was failed

in previous boot

Unplug the power cord, wait for 30

seconds, and reboot the server. If the same

error is detected repeatedly, contact your

service representative.

C11F

Backup Data of BMC Mezzanine

card has corrupted.

Inconsistency was found on BMC

mezzanine card.

Contact your sales representative.

C200

The error occurred during
memory configuration check.

Memory configuration could not be

obtained.

C201

Memory Configuration change is
detected.

The memory configuration has

changed since the previous startup.

When

Check previous system Config

enabled in

Server

menu of the setup, this

message appears if the configuration was

changed since the previous startup. If this

message appears even when no

configuration change has been made,

contact your service representative.

C202

The error occurred during CPU
configuration check.

The CPU information could not be

obtained.

Contact your service representative.

C203

CPU Configuration change is
detected.

The CPU configuration has changed

since the previous startup.

When

Check previous system Config

enabled in

Server

menu of the setup, this

message appears if the configuration was

changed since the previous startup. If this

message appears even when no

configuration change has been made,

contact your service representative.

Содержание Express5800/E120f-M






































































































































































Результаты поиска

Содержание Express5800/E120f-M

Отзывы:

Похожие инструкции для Express5800/E120f-M

Бренды по названию

Популярные бренды

NEC Express5800/E120f-M, Руководство по обслуживанию

Результаты поиска

Содержание Express5800/E120f-M

Отзывы:

Похожие инструкции для Express5800/E120f-M

Бренды по названию

Популярные бренды