NEC Express5800/E120f-M Скачать руководство пользователя

Страница: 164 / 165

4. Glossary

Express5800/E120f-M Maintenance Guide

164

Chapter 3 Appendix

Glossary

Terms

Description

BIOS Setup Utility (SETUP)

Software for setting BIOS. You can run this software by pressing <F2> key during

POST.

BMC

Baseboard Management Controller (BMC) is a built-in controller that supports the

IPMI version 2.0 protocol. BMC can manage the server hardware.

BMC RESET Switch

A switch for resetting the BMC of the server. This resets the BMC without clearing the

BMC settings.

Use the switch if the problem on the BMC occurs.

DUMP Switch

A switch that is used for collecting the memory dump if an error occurs. You can

specify the destination of the dump by using the Windows function.

EXPRESSBUILDER

Standard software for setting up the server easily. This also includes several useful

applications and instruction manuals.

EXPRESSSCOPE ENGINE 3

A name of BMC for NEC Express5800 series.

EXPRESSSCOPE Profile Key

A removable flash memory that stored the settings of BIOS and BMC. If the

motherboard of the server is replaced, you can use former settings when moving this

flash memory from the former motherboard.

Express Report Service

Software that can report the server failure to the contact center by E-mail or modem.

This software is installed with NEC ESMPRO ServerAgentService to the server.

Express Report Service (HTTPS)

Software that can report the server failure to the contact center by HTTPS. This

software is installed with NEC ESMPRO ServerAgentService to the server.

Express Report Service (MG)

Software that can report the server failure to the contact center by E-mail, modem or

HTTPS without NEC ESMPRO ServerAgentService. This software is installed with

NEC ESMPRO Manager to "PC for Management".

ExpressUpdate

A feature for updating BIOS, firmware, driver, or software of the server. This feature is

available when NEC ESMPRO Manager cooperates with EXPRESSSCOPE ENGINE

3 and ExpressUpdate Agent.

ExpressUpdate Agent

Software for performing ExpressUpdate. This is installed to the server.

Flash FDD

An optional USB device that can use as a floppy disk drive.

Internal Flash Memory

A built-in flash memory that stored EXPRESSBUILDER as standard. You can start

EXPRESSBUILDER from it without DVD when pressing <F3> key during POST.

NEC ESMPRO

Standard software for the server management. This consists of several applications

for managing or monitoring.

NEC ESMPRO Agent

Software for monitoring the server. This works with NEC ESMPRO Manager and

resides as the OS service.

NEC ESMPRO Agent Extension

Software for performing the scheduled operations. This works with NEC ESMPRO

Manager.

NEC ESMPRO Manager

Software for managing plural servers on network.

NEC ESMPRO ServerAgentService

Software for monitoring the server. This works with NEC ESMPRO Manager. You can

choose Service Mode or Non-Service Mode when installing this software. Service

Mode resides as the OS service and Non-Service Mode does not use the OS service

to reduce the OS resources such as memory or CPU.

OEM driver

A Windows driver for the mass storage device.

OS standard installer

An installer that stored in Windows installation disc. Use this installer if you want to

install the OS manually.

Offline tools

Software that can confirm or change IPMI data such as SEL, SDR, or FRU. You can

start Offline tools when pressing <F4> key during POST.

PC for Management

A computer for managing the server on network. A general Windows/Linux computer

can be used as "PC for Management".

Product Info Collection Utility

Software for collecting several hardware/software statuses or event logs. You can

easily collect the data for the server maintenance by using this software.

RAID Configuration Utility

Software for configuring RAID arrays. You can run this software during POST.

Server Configuration Utility

Software for setting BIOS or BMC. You can use as Windows application or run this

software when pressing <F4> key during POST. This software is the same as BMC

Configuration of former models.

Starter Pack

Software package for the server. This software includes the customized drivers for

Windows. This must be installed before using Windows on the server.

TPM Kit

An optional product of Trusted Platform Module for the server.

Universal RAID Utility

Software for setting RAID arrays on Windws/Linux. This software is operated on "PC

for Management" with NEC ESMPRO Manager.

Windows OS parameter file

A file that saved settings for installing Windows. You can install with the saved

settings in this file when setting Windows with EXPRESSBUILDER.

Содержание Express5800/E120f-M






































































































































































Результаты поиска

Содержание Express5800/E120f-M

Отзывы:

Похожие инструкции для Express5800/E120f-M

Бренды по названию

Популярные бренды

NEC Express5800/E120f-M, Руководство по обслуживанию

Результаты поиска

Содержание Express5800/E120f-M

Отзывы:

Похожие инструкции для Express5800/E120f-M

Бренды по названию

Популярные бренды