NEC Express5800/E120f-M Скачать руководство пользователя

Страница: 133 / 165

1. POST Error Message

Express5800/E120f-M Maintenance Guide

133

Chapter 3 Appendix

(1) Error messages

Error Message

Cause

Solution

8000

System variable is

corrupted.

Illegal setup information of BIOS was

detected.

Start BIOS Setup Utility (SETUP), and then

execute

Load Setup Defaults

and specify

the necessary settings.

If the same error is detected repeatedly in

spite of re-setting, contact your sales

representative.

8001

Real time clock error

Real time clock error was detected.

Start SETUP, and then specify the correct

date and time.

If the same error is detected repeatedly in

spite of re-setting, contact your sales

representative.

8002

Check date and time settings

Incorrect date and time set on real

time clock was detected.

8003

System battery is dead -

Replace and run SETUP

The battery for storing system settings

is dead.

Contact your sales representative.

After the replacement, start SETUP, and

then specify the correct settings.

8005

Previous boot incomplete -

Default configuration used

The previous POST processing did

not finish.

Use SETUP to specify the correct settings.

8006

System configuration data

cleared by Jumper.

SETUP settings were cleared by the

jumper.

Follow the steps described in

Chapter 1 (7.

Resetting and Clearing the Server).

Start SETUP, and then setup each item

again.

If the same error is detected repeatedly in

spite of re-setting, contact your sales

representative.

This error message also appears when

lithium battery is removed.

8007

SETUP Menu Password cleared

by Jumper.

The password for SETUP was cleared

by the jumper.

8020

BIOS update error.

BIOS update failed.

Try BIOS update again.

If the same error is detected repeatedly,

contact your sales representative.

8021

Recovery jumper is set, but

recovery images is not

found.

Recovery jumper is set, but recovery

image is not found.

Contact your sales representative.

8800

DXE_NB_ERROR

An error was detected during

initialization of chipset.

8801

DXE_NO_CON_IN

An error was detected during

initialization of console.

8802

DXE_NO_CON_OUT

8803

PEI_DXE_CORE_NOT_FOUND

A flash ROM for system is corrupt.

8804

PEI_DXEIPL_NOT_FOUND

8805

DXE_ARCH_PROTOCOL_NOT_AVA

ILABLE

8806

PEI_RESET_NOT_AVAILABLE

The system was not reset correctly.

8807

DXE_RESET_NOT_AVAILABLE

8808

DXE_FLASH_UPDATE_FAILED

A flash ROM for system was not

written to correctly.

8830

PEI_RECOVERY_NO_CAPSULE

A flash ROM for system was not

recovered correctly.

8831

PEI_RECOVERY_PPI_NOT_FOUN

8832

PEI_RECOVERY_FAILED

9000

Unsupported CPU detected

An unsupported CPU was detected.

9001

Unsupported CPU detected on

CPU #1

9002

Unsupported CPU detected on

CPU #2

9021

Unsupported CPU Speed

detected on CPU #1

A CPU of which clock speed is

unsupported was detected.

9022

Unsupported CPU Speed

detected on CPU #2

Содержание Express5800/E120f-M






































































































































































Результаты поиска

Содержание Express5800/E120f-M

Отзывы:

Похожие инструкции для Express5800/E120f-M

Бренды по названию

Популярные бренды

NEC Express5800/E120f-M, Руководство по обслуживанию

Результаты поиска

Содержание Express5800/E120f-M

Отзывы:

Похожие инструкции для Express5800/E120f-M

Бренды по названию

Популярные бренды