Figure 3.6 Set period at memory displayed
Remote sense, internal control, external control, and interlock can be selected or deselected when
the rem sen, int ctl, ext ctl, or loc LED is flashing. To select, press enter or to deselect, press
clear. Remote sense allows the output voltage to be sensed at the load rather than at the output
terminals of the power supply. This feature eliminates regulation degradation caused by the
voltage drop across the output cables. Details on the physical connections are covered in Section
3.3.
Internal control enables the start, stop, arm, and clear keys on the front panel. External control
enables the start, stop, arm, and clear inputs at terminals 17, 19, 36, and 18 of connector JS1 on
the rear panel, respectively. Both internal control and external control may be enabled to allow
simultaneous control. Interlock requires a physical short between terminals 26 and 37 of
connector JS1 to enable operation. This feature is useful for process control applications when a
safety interlock is required. For wiring details, refer to Section 3.6.
Configuration commands for rotary, keypad, external program, and remote set the reference
input mode for voltage set, current set, over voltage trip, and over current trip. Only one input
mode may be selected. Pressing enter when one of the respective LED is flashing causes that
mode to be selected and disables the previously selected mode. Pressing clear when the
respective LED is flashing allows the user to exit the command sequence without change. With
rotary control,
33
Содержание DP SERIES II
