mori seiki NL1500/500, Руководство по обслуживанию, Страница: 208 / 245

ӏࡾጀ࣊ȟҋȽȗȻȠ
WHEN SUB-STANDARD MACHINING OCCURS
208
11)
˩َɁɛșȾфᜏሰ͇Ƞඨɔɀȫ
2
Ȟ੔ɁҋоɝȾɛȶȹ
˿ᢉիɁ஁տɥᝩ୥ȺȠɞǿȹȦࣻʊɮʮʵɼ˂ʂɥȕɞ
ሌ࣊ɁᄻާȾȪȹǾ˿ᢉիɥ़ȁȾᝩ୥Ȭɞǿ
11)
As shown in the diagram below, headstock inclination is
adjusted by loosening/tightening the 2 hexagon socket set
screws with a hex wrench. Using the lever type dial test
indicators as a reference, gradually adjust the inclination of
the headstock.
12)
фᜏʶʽʋȺ˿ᢉի˩᥂Ɂфᜏሰ͇Ƞʦʵʒ
2
Ȟ੔ɥ፻ɔ
ɞǿ
12)
Using a hex wrench, tighten the 2 hexagon socket head
cap screws at the base of the headstock.
13)
фᜏʶʽʋȺ˿ᢉիِްႊɁфᜏሰ͇Ƞʦʵʒ
6
Ȟ੔ɥ፻
ɔɞǿ
13)
Using a hex wrench, firmly tighten the 6 hexagon socket
head cap screws to secure the headstock.
14)
ȹȦࣻʊɮʮʵɼ˂ʂɥ՘ɝ۶Ȭǿ
14)
Remove the lever type dial test indicators.
15)
ൡಽ᫖ໃɥੵоȬɞǿ
15)
Turn ON the main power.
16)
ʐʃʒӏࡾɥᚐșǿ
16)
Perform test machining.
7
า৙
7
CAUTION
ɵʚ˂ɥ՘ɝ۶ȪȲ࿡ৰȺ˿ᢉɥوᢆȨȮɞ᪨ȾɂǾԚґ
า৙ȪȹȢȳȨȗǿوᢆ᥂ɗժӦ᥂ґɁᩖȾਖ਼ȟࢊȠᣅɑ
ɟǾ̷ᡵ̜୒ȾȷȽȟɝɑȬǿ
Exercise extreme caution when rotating the spindle
with covers removed to prevent entanglement in
rotating/moving parts, resulting in serious injury.
17)
ʹ˂ɹɁяኋ࣊ɥѓ࣊ລްȪɑȬǿ॒ᛵȾख़ȫȹǾਖ਼ᬲ
4)
ᵻ
6)
ȝɛɆ
9)
ᵻ
16)
ɥᎱɝᣌȬǿ
17)
Measure the workpiece roundness using a micrometer. If
necessary, perform steps
4)
to
6)
and
9)
to
16)
again to
readjust.
18)
՘۶ȪȻᣡɁਖ਼ᬲȺǾɵʚ˂ɥ՘ɝ͇Ȥɞǿ
18)
Remount the covers by following the removal procedure in
reverse.
12-3
ҏ࿎իɁϿȠᝩ୥
Turret Inclination Adjustment
ҏ࿎իȟ̜୒ȽȼȾɛɝϿȗȲȻȠǾ͏˩Ɂਖ਼ᬲȺҏ࿎իɁ
ϿȠɥᝩ୥ȪȹȢȳȨȗǿ When turret tilting occurs due to component interference,
adjust the turret inclination according to the following
procedure.
ᴹႊ৙ȬɞɕɁᴻ
<Necessary Tools>
•
ʨɺʗʍʒʃʉʽʓ
• Magnet stand
•
ȹȦࣻʊɮʮʵɼ˂ʂ • Lever type dial test indicators
•
фᜏʶʽʋ • Hex wrench
Hexagon Socket Set Screws (2) Hexagon Socket Head Cap Screws (2)
фᜏሰ͇Ƞඨɔɀȫᴥ
2
Ȟ੔ᴦ фᜏሰ͇Ƞʦʵʒᴥ
2
Ȟ੔ᴦ