Mita PointSource Ai 3010 Скачать руководство пользователя страница 259

Страница: 259 / 478

3-2-83-1

2AR-1

Mainte-

nance

Description

item No.

U907

Setting the paper eject location when used as a printer/fax

Description
Sets the paper eject location when an optional device for using the copier
as a printer or fax is installed.

Purpose
Used to change the paper eject location when the copier is used as a
printer or fax.

Method

1. Press the start key. The screen for selecting an item is displayed.
2. Select the item (printer or fax) to be set using the cursor up/down

keys.

3. Press the start key. The screen for the selected item is displayed.

Setting

1. Select the paper eject location using the cursor up/down keys.

Eject tray
Job separator

Display

INNER TRAY
JOB SEPARATOR

Paper eject location

• Printer

Eject tray
Other paper eject locations*

Display

IINNER TRAY
OTHER

Paper eject location

• Fax

Mailbox

Job separator

Mailbox mail tray 1

Present

Not present

Job separator

Eject tray

* Other paper feed locations

Job
separator

Present

Not present

2. Press the start key. The value is set, and the screen for selecting an

item is displayed.

Completion
Press the stop/clear key at the screen for selecting an item. The screen for
selecting a maintenance item No. is displayed.

Содержание PointSource Ai 3010































































































































































































































































































































































































































































































Результаты поиска

Содержание PointSource Ai 3010

Отзывы:

Похожие инструкции для PointSource Ai 3010

Бренды по названию

Популярные бренды

Mita PointSource Ai 3010, Руководство по обслуживанию

Результаты поиска

Содержание PointSource Ai 3010

Отзывы:

Похожие инструкции для PointSource Ai 3010

Бренды по названию

Популярные бренды