Mita PointSource Ai 3010 Скачать руководство пользователя страница 181 | Manualshive

Страница: 181 / 478

background image

3-2-52

2AR

Mainte-

nance

Description

item No.

U156

Changing the toner control level

Description
Changes the toner feed start level set in maintenance item U130 or the
toner empty level to be determined by the difference from the toner feed
start level.

Purpose
To check the toner feed start level and toner empty level.

Method
Press the start key. The screen for selecting an item is displayed.

Toner feed start level
Difference between the toner feed start
level and toner empty level

Display

TARGET
EMPTY

Description

Setting for the toner feed start level

1. Select TARGET using the cursor up/down keys.
2. Change the setting using the cursor left/right key.

0 to 255

Description

Toner feed start level

Setting range

Increasing the setting makes the toner density lower.

3. Press the start key. The value is set.

Setting for the toner empty level

1. Select EMPTY using the cursor up/down keys.
2. Change the setting using the cursor left/right key.

0 to 255

Description

Difference between
the toner feed start level
and the toner empty level

Setting range

Increasing the setting makes the toner empty level higher: the toner
density is lower when the toner empty is detected.

3. Press the start key. The value is set.

Completion
Press the stop/clear key. The screen for selecting maintenance item No. is
displayed.

«
...
179
180
181
182
183
...
»

Содержание PointSource Ai 3010































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для PointSource Ai 3010

Бренд: Olivetti Страницы: 587

DCP 385C - Color Inkjet - All-in-One

Бренд: Brother Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды