Mita PointSource Ai 3010 Скачать руководство пользователя страница 155

Страница: 155 / 478

3-2-26

2AR-1

Mainte-

nance

Description

item No.

U070

Adjusting the DF magnification

Description
Adjusts the DF original scanning speed.

Purpose
To be executed if the correct magnification is not obtained in the auxiliary
scanning direction when the optional SRDF is used.

Caution
Before making this adjustment, ensure that the following adjustments have
been made in maintenance mode.

U053

U034

U402

U070

U071

U072

U404

Method
Press the start key.

Setting

1. Change the setting using the cursor left/right keys.

Display

CONVEY SPEED

Description

Change in value

per step

Initial

setting

Setting

range

Original conveying
motor speed

–25 to +25

0.1%

Increasing the setting makes the image longer, and decreasing it
makes the image shorter.

2. Press the start key. The value is set.

Interrupt copy mode
While this maintenance item is being performed, copying from an original
can be made in interrupt copy mode.

Completion
Press the stop/clear key. The screen for selecting a maintenance item No.
is displayed.

Содержание PointSource Ai 3010































































































































































































































































































































































































































































































Результаты поиска

Содержание PointSource Ai 3010

Отзывы:

Похожие инструкции для PointSource Ai 3010

Бренды по названию

Популярные бренды

Mita PointSource Ai 3010, Руководство по обслуживанию

Результаты поиска

Содержание PointSource Ai 3010

Отзывы:

Похожие инструкции для PointSource Ai 3010

Бренды по названию

Популярные бренды