Mircom FR-320 Series Скачать руководство пользователя страница 92

Страница: 92 / 112

Pre-Programmed Modes

12.13 Mode 13: Pre-action/deluge, Single Hazard, Not Cross Zoned,

Combined Release

12.13.1 Zone Configuration

•

Detection Zone -1: Alarm (Hazard Area 1, not cross-zoned)

•

Detection Zone -2: Alarm (Hazard Area 1, not cross-zoned)

•

Detection Zone -3: Alarm (Hazard Area 1, not cross-zoned)

•

Detection Zone -4: Supervisory

•

Detection Zone -5: Supervisory

•

Detection Zone -6: Water-flow.

•

NAC -1: Signal, steady on any alarm.

•

NAC -2: Escalating signal, indicates Hazard Area 1 status, Supervisory Optional.

•

RAC -1: Releasing Circuit (Hazard Area 1)

•

RAC -2: Releasing Circuit (Hazard Area 1)

12.13.2 Hazard Configuration

•

Default Release Timer Value: 0 seconds

•

Default Manual Release Delay: 0 seconds (not used)

•

Default Abort Delay Type: Standard UL (not used)

•

Default Soak Timer Value: 0 seconds (continuous)

12.13.3 NAC Configuration

•

Default Escalating NAC code of Hazard Area State:

•

Hazard Idle: Off

•

Hazard Alert: Temporal (see Table 7)

•

Hazard Alarm: Temporal (see Table 7)

•

Hazard Release: Steady

•

Default NAC code of Supervisory is 20 BPM.

12.13.4 How the Panel Works in Mode 13

•

Activation of any one among Z-1, Z-2 or Z-3 changes Hazard Area 1 state into Alarm.
Release Timer-1 is started. NAC-1 turns on at Temporal. Upon the expiration of Release
Timer-1, NAC-1 turns on steady. RAC-1and RAC-2 are activated.

•

Activation of Z4 or Z-5 can be indicated on NAC-2 at 20 BPM, if configured.

Detection Zones

Phantom Zones

Zp1

RT1

Exp

Alm

Supv

Z1+Z2+Z3

Out1

Signal

Steady

Out2

Signal

Escalating

(X)

Out3

Rel.

Releasing

Out4

Rel.

Releasing

RLS TMR 1 Started

RLS Tmr 1 Interrupted

RLS Tmr 1 Cancelled

Содержание FR-320 Series

















































































































Результаты поиска

Содержание FR-320 Series

Отзывы:

Похожие инструкции для FR-320 Series

Бренды по названию

Популярные бренды

Mircom FR-320 Series, Инструкция по установке и эксплуатации

Результаты поиска

Содержание FR-320 Series

Отзывы:

Похожие инструкции для FR-320 Series

Бренды по названию

Популярные бренды