Mircom FR-320 Series Скачать руководство пользователя страница 65

Страница: 65 / 112

Configuration

10.11 8. Test Dialer (Command-Menu)

10.11.1 Dialer Test Messages

The following messages will display during the test processes of Lines #1 and #2. The
messages that will appear depend on the status of the dialer and the test results that are
found.

Press Enter to test Line #1. Press Cancel to exit this menu. For
a description of test messages, see

Dialer Test Messages

below.

Press Enter to test Line #2. Press Cancel to exit this menu. For
a description of test messages, see

Dialer Test Messages

below.

This feature flushes all reportable events from the buffer. Press
Enter to reset the dialer. Press Cancel to exit this menu.

The dialer is checking the line for voltage. This message
automatically displays when Manual Test is selected.

No DC line voltage. The line is dead or no phone line is connected.

The dialer is waiting for a dial tone.

This message may indicate a noisy telephone line.

-Dialer Test-

1. L#1 Manual test
2. L#2 Manual test
3. Reset Dialer

L#1 Manual test

L#2 Manual test

3. Reset Dialer

Dialer idle now

No DC Volt

Waiting for Dialtone

Failed: No Dialtone

Содержание FR-320 Series

















































































































Результаты поиска

Содержание FR-320 Series

Отзывы:

Похожие инструкции для FR-320 Series

Бренды по названию

Популярные бренды

Mircom FR-320 Series, Инструкция по установке и эксплуатации

Результаты поиска

Содержание FR-320 Series

Отзывы:

Похожие инструкции для FR-320 Series

Бренды по названию

Популярные бренды