Mircom FR-320 Series Скачать руководство пользователя страница 71

Страница: 71 / 112

Pre-Programmed Modes

12.2

Mode 2: Agent Release, Single Hazard, Not Cross-zoned,
Combined Release

12.2.1 Zone Configuration

•

Detection Zone -1: Alarm (Hazard Area 1, not cross-zoned)

•

Detection Zone -2: Alarm (Hazard Area 1, not cross-zoned)

•

Detection Zone -3: Alarm (Water-flow or pressure switch)

•

Detection Zone -4: Supervisory (default non-latching)

•

Detection Zone -5: Abort Switch

•

Detection Zone -6: Manual Release

•

NAC-1: Signal, will be on steady if there is any alarm zone or manual release switch
active.

•

NAC-2: Signal, indicates the cadence of hazard area 1 state or supervisory circuit
(optional).

•

RAC-1: Releasing Circuit (Hazard Area 1)

•

RAC-2: Releasing Circuit (Hazard Area 1)

12.2.2 Hazard Configuration

•

Default Release Timer Value: 60 seconds

•

Default Manual Release Delay: 0 seconds.

•

Default Abort Delay Type: Standard UL.

•

Default Soak Timer Value: 0 seconds

12.2.3 NAC Configuration

•

Default Escalating NAC code of Hazard Area State:

•

Hazard Idle: Off

•

Hazard Alert: Temporal (see Table 7)

•

Hazard Alarm: Temporal

•

Hazard Release: Steady

•

Default NAC code of Supervisory Signal is 20 BPM.

Detection Zones

Phantom Zones

Release Timers

Zp1

Zp2

RT1

Exp

RT2
Exp

Alm

Sup

Z1+Z2

Z3+Z4

Out1

Signal

Steady

Out2

Signal

Escalating

(X)

Out3

Rel.

Releasing

Out4

Rel.

Releasing

RLS TMR 1 Started

RLS Tmr 1 Interrupted

RLS Tmr 1 Cancelled

RLS Tmr 2 Started

RLS Tmr 2 Interrupted

RLS Tmr 2 Cancelled

Содержание FR-320 Series

















































































































Результаты поиска

Содержание FR-320 Series

Отзывы:

Похожие инструкции для FR-320 Series

Бренды по названию

Популярные бренды

Mircom FR-320 Series, Инструкция по установке и эксплуатации

Результаты поиска

Содержание FR-320 Series

Отзывы:

Похожие инструкции для FR-320 Series

Бренды по названию

Популярные бренды