Mircom FR-320 Series Скачать руководство пользователя страница 5

Страница: 5 / 112

Table of Contents

9.1.5

Remote Trouble .............................................................................................................

9.1.6

Ground Fault ..................................................................................................................

9.1.7

CPU Fail .........................................................................................................................

9.1.8

Abort ..............................................................................................................................

9.1.9

Released ........................................................................................................................

9.1.10

System Reset .................................................................................................................

9.1.11

Signal Silence ................................................................................................................

9.1.12

Auxiliary Disconnect .......................................................................................................

9.1.13

Lamp Test ......................................................................................................................

9.1.14

ALM/SUP/TBL/BLDG AUDIBLE SIL (Buzzer Silence) ...................................................

9.1.15

Pre Release ...................................................................................................................

9.2

Menu Buttons .................................................................................................................

9.3

Switches and Common Indicators .................................................................................

9.3.1

Zone 1 to Zone 4 ............................................................................................................

9.3.2

Zone 5 and Zone 6 .........................................................................................................

9.3.3

Out1 and Out2 (NAC circuits) ........................................................................................

9.3.4

Out3 and Out4 (Releasing circuits) ................................................................................

9.3.5

Input Circuits Bypass Switch ..........................................................................................

9.3.6

Output Circuits Bypass Switch .......................................................................................

9.4

Common Controls ..........................................................................................................

9.4.1

System Reset Button .....................................................................................................

9.4.2

Signal Silence Button .....................................................................................................

9.4.3

Auxiliary Disconnect Button ...........................................................................................

9.4.4

Lamp Test Button ...........................................................................................................

9.4.5

ALM/SUP/TBL/BLDG AUDIBLE SIL Button (Buzzer Silence) .......................................

9.5

Circuit (zone) disconnect buttons ...................................................................................

9.6

Common Relays ............................................................................................................

9.7

Circuit Types ..................................................................................................................

9.7.1

Initiating (Detection) Circuit Types .................................................................................

9.7.2

Non-Verified Alarm .........................................................................................................

9.7.3

Water Flow Alarm (Water flow Sensors) .......................................................................

9.7.4

Non-Latching Supervisory (For Supervisory Circuits) ...................................................

9.7.5

Latching Supervisory (For Supervisory Devices) ...........................................................

9.7.6

Abort Switch ...................................................................................................................

9.7.7

Manual Release Switch .................................................................................................

9.7.8

Indicating (Signal) Circuits Types ..................................................................................

9.7.9

Silenceable Signal .........................................................................................................

9.7.10

Non-Silenceable Signal ..................................................................................................

9.7.11

Silenceable Strobe .........................................................................................................

9.7.12

Non-Silenceable Strobes ...............................................................................................

9.8

Evacuation codes ...........................................................................................................

10.0

Configuration 47

10.1

Using the CFG-300 Tool ................................................................................................

Содержание FR-320 Series

















































































































Результаты поиска

Содержание FR-320 Series

Отзывы:

Похожие инструкции для FR-320 Series

Бренды по названию

Популярные бренды

Mircom FR-320 Series, Инструкция по установке и эксплуатации

Результаты поиска

Содержание FR-320 Series

Отзывы:

Похожие инструкции для FR-320 Series

Бренды по названию

Популярные бренды