Mircom FR-320 Series Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 112

background image

25

Cable and Jumper Connections for Main Board, Core Board and Adder Modules

6.3

OCAC-302 Output Class-A Converter Adder Module

Figure 8 OCAC-302 Output Class-A Converter Adder Module

Indicating circuits must be wired from the OCAC-302 to the main Fire Alarm board. For
example indicating circuit 1 positive (red wire) and negative (black wire) is wired from the
Class A converter module to the positive and negative terminals of Indicating circuit 1 on the
Main Fire Alarm board.

The actual indicating zone is wired from the SIGNAL OUT positive and negative to the
signaling devices and then wired back to the SIGNAL RET positive and negative.

6.4

RM-306 Relay Adder Module

Cable from P1 of the RM-306 is connected to P4 on the Main Fire Alarm Board. The jumpers
located above each relay on the RM-306 are used to configure the relays. The jumpers
located below the relays are used to select either normally open contacts or normally closed
contacts.

Figure 9 RM-306 six relay adder module

- S

IG

1

O

UT

+

- S

IG

2

O

U

T+

- S

IG

1

R

ET

+

- S

IG

2

R

ET

+

BL

K

RE

D

BL

K

RE

D

mounting hole for

#6-32 screws

OCAC-302

mounting hole for
#6-32 screws

NO/NC C

RELAY 1

NO/NC C

RELAY 2

NO/NC C

RELAY 3

NO/NC C

RELAY 4

C

RELAY 5

NO/NC C

RELAY 6

NO/NC

mounting hole
for #6-32 screws

mounting hole
for #6-32 screws

INDIVIDUAL GREEN
RELAY STATUS LEDs

Connect to P6 on the
main fire alarm board

6

«
...
23
24
25
26
27
...
»

Содержание FR-320 Series

















































































































Отзывы:

Нет отзывов

Похожие инструкции для FR-320 Series

Бренд: GARDTEC Страницы: 48

Бренд: FAAC Страницы: 64

Бренд: Balboa Instruments Страницы: 10

Бренд: Quantum Data Страницы: 36

Бренд: Samson Страницы: 20

Бренд: CAME Страницы: 18

Бренд: CAME Страницы: 28

Бренд: CAME Страницы: 28

Бренд: CAME Страницы: 4

Бренд: CAME Страницы: 40

Бренд: CAME Страницы: 26

Бренд: CAME Страницы: 34

Бренд: CAME Страницы: 2

Бренд: HABONIM Страницы: 9

Бренд: Paradox Страницы: 32

Omnicharge Solar OCS 100-20

Бренд: tbs electronics Страницы: 64

Бренд: National Instruments Страницы: 14

Бренд: MaintTech Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды