Mircom FR-320 Series Скачать руководство пользователя страница 37 | Manualshive

Страница: 37 / 112

background image

37

8.0

System Checkout

8.1

Before turning the power “ON”

To prevent sparking,

do not connect

the batteries. Connect the batteries after powering the

system from the main AC supply.

1. Check that all modules are installed in the proper location with the proper connections.

2. Check all field (external) wiring for opens, shorts, and ground.

3. Check that all interconnection cables are secure, and that all connectors are plugged in

properly.

4. Check all jumpers and switches for proper setting.

5. Check the AC power wiring for proper connection.

6. Check that the chassis is connected to

EARTH GROUND

(cold water pipe).

7. Make sure to

close the front cover plate

before powering the system from main AC

supply.

The best way to check out a panel first is to not connect any field wiring. Power up the panel
with an end of line. The panel should be free of trouble. Then connect one circuit at one time.
If a trouble occurs, correct the fault then continue the field wiring.

8.2

Power-up procedure

After completing the System Checkout procedures outlined above,

1. Power up the panel. The "AC ON" green LED and the “Common Trouble” LED should

illuminate, and the buzzer should sound. Press the “System Reset” button. Since the
batteries are not connected, the trouble buzzer should sound intermittently and the
common trouble LED should flash.

2. Connect the batteries while observing correct polarity: the red wire is positive (+) and

black wire is negative (-). All indicators should be OFF except for normal power "AC ON"
green LED and green LED I4 (below the TROUBLE relay at left bottom of board).

3. Configure the Fire Alarm Control Panel as described in the Configuration section.

Note:

Green LED I4 is illuminated when the system is normal. This LED indicates that
the trouble relay is in normal standby condition.

i

«
...
35
36
37
38
39
...
»

Содержание FR-320 Series

















































































































Отзывы:

Нет отзывов

Похожие инструкции для FR-320 Series

Бренд: FAAC Страницы: 12

Бренд: Unipulse Страницы: 99

Бренд: Accutrol Страницы: 25

Бренд: Mainpine Страницы: 16

Бренд: Danfoss Страницы: 20

Бренд: UNITED Страницы: 22

Бренд: Faulhaber Страницы: 66

Бренд: Federal Signal Corporation Страницы: 34

Бренд: hager Страницы: 62

coviva Smartbox TKP100A

Бренд: hager Страницы: 45

Бренд: Eaton Страницы: 2

Бренд: Union Instruments Страницы: 63

Бренд: Sunnen Страницы: 24

Бренд: FUTABA Страницы: 8

Бренд: Acuity Controls Страницы: 5

Бренд: Risco Страницы: 232

CompleteStat-Series CS9B-THO

Бренд: Bard Страницы: 2

Бренд: Delabie Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды