Mircom FR-320 Series Скачать руководство пользователя страница 7

Страница: 7 / 112

Table of Contents

12.3.2

Hazard Configuration .....................................................................................................

12.3.3

NAC Configuration .........................................................................................................

12.3.4

How the Panel Works in Mode 3 ....................................................................................

12.4

Mode 4: Agent Release, Dual Hazard, Not Cross-zoned, Split Release .......................

12.4.1

Zone Configuration ........................................................................................................

12.4.2

Hazard Configuration .....................................................................................................

12.4.3

NAC Configuration .........................................................................................................

12.4.4

How the Panel Works in Mode 4 ....................................................................................

12.5

Mode 5: Pre-action/Deluge, Single Hazard, Cross-zoned, Combined Release .............

12.5.1

Zone Configuration ........................................................................................................

12.5.2

Hazard Configuration .....................................................................................................

12.5.3

NAC Configuration .........................................................................................................

12.5.4

How the Panel Works in Mode 5 ....................................................................................

12.6

Mode 6: Pre-action/Deluge, Single Hazard, Not Cross-zoned, Combined Release ......

12.6.1

Zone Configuration ........................................................................................................

12.6.2

Hazard Configuration .....................................................................................................

12.6.3

NAC Configuration .........................................................................................................

12.6.4

How the Panel Works in Mode 6 ....................................................................................

12.7

Mode 7: Pre-action/Deluge, Dual Hazard, Cross-zoned, Split Release .........................

12.7.1

Zone Configuration ........................................................................................................

12.7.2

Hazard Configuration .....................................................................................................

12.7.3

NAC Configuration .........................................................................................................

12.7.4

How the Panel Works in Mode 7 ....................................................................................

12.8

Mode 8: Pre-action/Deluge, Dual Hazard, Not Cross-zoned, Split Release ..................

12.8.1

Zone Configuration ........................................................................................................

12.8.2

Hazard Configuration .....................................................................................................

12.8.3

NAC Configuration .........................................................................................................

12.8.4

How the Panel Works in Mode 8 ....................................................................................

12.9

Mode 9: Agent Release, Single Hazard, Cross-zoned, NYC abort ................................

12.9.1

Zone Configuration ........................................................................................................

12.9.2

Hazard Configuration .....................................................................................................

12.9.3

NAC Configuration .........................................................................................................

12.9.4

How the Panel Works in Mode 9 ....................................................................................

12.10

Mode 10: Agent Release, Single Hazard, Not Cross-zoned, Combined Release .........

12.10.1

Zone Configuration ........................................................................................................

12.10.2

Hazard Configuration .....................................................................................................

12.10.3

NAC Configuration .........................................................................................................

12.10.4

How the Panel Works in Mode 10 ..................................................................................

12.11

Mode 11: Agent Release, Single Hazard, Cross-zoned, Combined Release ................

12.11.1

Zone Configuration ........................................................................................................

12.11.2

Hazard Configuration .....................................................................................................

12.11.3

NAC Configuration .........................................................................................................

12.11.4

How the Panel Works in Mode 11 ..................................................................................

12.12

Mode 12: Pre-action/Deluge, Single Hazard, Cross Zoned, Combined Release ..........

12.12.1

Hazard Configuration .....................................................................................................

Содержание FR-320 Series

















































































































Результаты поиска

Содержание FR-320 Series

Отзывы:

Похожие инструкции для FR-320 Series

Бренды по названию

Популярные бренды

Mircom FR-320 Series, Инструкция по установке и эксплуатации

Результаты поиска

Содержание FR-320 Series

Отзывы:

Похожие инструкции для FR-320 Series

Бренды по названию

Популярные бренды