manualshive.com logo in svg

MIMAKI Kebab MKII, Руководство по эксплуатации

Поделиться
Скачать
MIMAKI Kebab MKII Скачать руководство пользователя страница 34

Use the work holder

34

5

Tighten the screws (2 pieces) retaining 
the right work holder.

6

Put the ball part of the right work holder 
and the work together.

7

Place the left work holder close to the 
work.

• Place the work and left work holder several centimeters away 

from each other to adjust the left work holder later.

8

Align the height of the ball part of the left work holder with the flat 
part of the side of the work.

• Loosen the thumbscrew of the supporting section of the ball, adjust the height, and then tighten the nut.
• When lining it up with the side that is uneven, it may affect drawing; try to line it up with the part that is as flat 

as possible.

9

Slide the left work holder, and put the 
ball part of the left work holder lightly to 
the work.

• Make sure that the work holder and the ball 

touch each other lightly; otherwise the work 
may raise and affect drawing depending on 
the mass of work.

Screw

How to loosen or tighten

Ball part to line up 
with the work

Содержание Kebab MKII

























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды