MIMAKI Kebab MKII Скачать руководство пользователя | Manualshive

Страница: 22 / 56

background image

Installation of Kebab MkII system

22

(5) Fix the Kebab MkII L system into place with a plastic

knob screw while pressing it into the K positioner BKT_R
(L) side.

16

Insert the option relay cable into the
connector on the printer.

• Surely insert the cable to prevent printer from coming off

during the operation.

17

Insert the option relay cable into the
connector on the rear surface of Kebab
MkII L system.

• Surely insert the cable to prevent printer from coming off

during the operation.

18

Fix the option relay cable with the
clamps.

• Fix the option relay cable with the clamp attached in the cable

BKT.

19

Press the

key.

• Printer performs Kebab MkII L system automatic recognition operation.

• Check that there is no gap between Kebab MkII L system and the table.
• If there is gap, perform the procedures below:

Lightly push Kebab MkII L system into from above.
Check that there is no dust etc. on the UJF-6042MkIIseries table.
Check that no dust adheres to the rear surface of Kebab MkII L system.

Direction

to push

Direction

to push

Option relay cable

Option relay cable

Option relay cable

Clamp

S E T O P T I O N J I G

J i g

: K e b a b M k II

L

ENTER

«
...
20
21
22
23
24
...
»

Содержание Kebab MKII

























































Отзывы:

Нет отзывов

Похожие инструкции для Kebab MKII

Бренд: DataCard Страницы: 8

Бренд: DataCard Страницы: 8

Бренд: DataCard Страницы: 3

WorkCentre 7655

Бренд: Xerox Страницы: 24

Бренд: Oki Страницы: 40

5550B - Phaser B/W Laser Printer

Бренд: Xerox Страницы: 117

WorkCentre 3345

Бренд: Xerox Страницы: 18

Бренд: Pantum Страницы: 126

Бренд: EFI Страницы: 4

Бренд: LevelOne Страницы: 88

Ecosys FS-1800+

Бренд: Kyocera Mita Страницы: 31

Бренд: LulzBot Страницы: 3

Бренд: SPRT Страницы: 21

Бренд: Astro Machine Страницы: 5

Бренд: Ricoh Страницы: 24

Бренд: Pantum Страницы: 95

Бренд: Compaq Страницы: 238

Бренд: Canon Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды