manualshive.com logo in svg

MIMAKI Kebab MKII, Руководство по эксплуатации

Поделиться
Скачать
MIMAKI Kebab MKII Скачать руководство пользователя страница 15

Installation of Kebab MkII system

15

(5) Fix the Kebab MkII system into place with a plastic knob 

screw while pressing it into the K positioner BKT_R (L) 
side.

14

Insert the option relay cable into the 
connector on the printer.

• Surely insert the cable to prevent printer from coming off 

during the operation.

15

Insert the option relay cable into the 
connector on the rear surface of Kebab 
MkII system.

• Surely insert the cable to prevent printer from coming off 

during the operation.

16

Fix the option relay cable with the 
clamps.

• Fix the option relay cable with the clamp attached in the cable 

BKT.

17

Press the 

 key.

• Printer performs Kebab MkII system automatic recognition operation.

• Check that there is no gap between Kebab MkII system and the table.
• If there is gap, perform the procedures below:

Lightly push Kebab MkII system into from above.
Check that there is no dust etc. on the UJF-3042MkIIseries table.
Check that no dust adheres to the rear surface of Kebab MkII system.

Direction 

to push

Direction 

to push

Option relay cable

Option relay cable

Option relay cable

Clamp

S E T O P T I O N J I G

J i g

: K e b a b M k II

ENTER

Содержание Kebab MKII

























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды