MIMAKI Kebab MKII Скачать руководство пользователя | Manualshive

Страница: 39 / 56

background image

Use the origin mark detection

39

4

Align the positions of the origin mark of
the work and the origin mark sensor.

5

Tighten the screws and fix the origin mark sensor.

When not using the Origin mark sensor

Attach the Origin mark sensor cover when not using the Origin mark sensor as to prevent contaminants such as ink
and dust from entering.

• You can check the origin mark sensor and origin point mark by making settings for the work or

Kebab.

• The Origin mark sensor is fixed in place with magnets near the Origin sensor.

origin mark sensor

Origin mark sensor cover

«
...
37
38
39
40
41
...
»

Содержание Kebab MKII

























































Отзывы:

Нет отзывов

Похожие инструкции для Kebab MKII

Бренд: Panasonic Страницы: 155

Бренд: Panasonic Страницы: 160

Бренд: Samsung Страницы: 165

Бренд: Samsung Страницы: 2

Inkjet SCX-1150F

Бренд: Samsung Страницы: 66

Бренд: Samsung Страницы: 155

CLX-3170FN series

Бренд: Samsung Страницы: 220

CLX 6210FX - Color Laser - All-in-One

Бренд: Samsung Страницы: 36

CLX-3160 Series

Бренд: Samsung Страницы: 139

Бренд: Samsung Страницы: 8

Lazett Combo SCX-4016

Бренд: Samsung Страницы: 2

Бренд: Samsung Страницы: 319

Бренд: 3D Systems Страницы: 26

Бренд: 3D Systems Страницы: 39

WorkSeries 200 Series

Бренд: 3D Platform Страницы: 9

Бренд: Oce Страницы: 192

Бренд: Oce Страницы: 22

Бренд: Oce Страницы: 41

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды