MIMAKI Kebab MKII Скачать руководство пользователя | Manualshive

Страница: 5 / 56

background image

For safe operation

5

WARNING

Power supply and voltage

• Use this machine with indicated power specifications.

Be sure to connect the power cable plug to the grounded outlet, or it may cause fire or electric shock.

• Never look at the LED UV being lit with your naked eyes, or it may cause pain in your eyes or visual impairment. Be

sure to wear safety glasses.

• Do not apply ultraviolet (UV) light directly to your skin, or it may cause irritation on your skin.
• To prevent electrical shock, be sure to set OFF the main power circuit breaker and disconnect the power plug

before carrying out maintenance. For some units, capacitors may take one minute for discharging; therefore, start
maintenance work three minutes after setting OFF the main power circuit breaker and disconnecting the power
plug.

• If LED UV has been damaged, you should replace the LED UV that has reached or has past its rating life.
• The main power circuit breaker should be set ON only by personnel with sufficient knowledge about operations of

this machine.

• Do not touch the lamp with bare hands while lighting or right after the lamp off to avoid from burn injury.

Handling of LED UV

• Do not use the LED UV in an ambience with a possibility of catching fire (gasoline, combustible gas spray, thinner,

lacquer, powder dust, etc.). In addition, do not put paper or cloth near or on the LED UV, or it may cause fire, or it
may cause electrical shock.

Handling of the antifreeze liquid

• Use the exclusive antifreeze liquid, or the cooling device may be damaged.
• If the antifreeze liquid or mixed soft water with antifreeze liquid gets on the skin or clothes, immediately wash it off

with soap.
If you get the antifreeze liquid in your eyes, immediately wash your eyes with a lot of clean water. Then, consult a
doctor as soon as possible.

• Before using the antifreeze liquid, be sure to read the Material Safety Data Sheet (MSDS).
• If you swallowed the antifreeze liquid accidentally, try to get to vomit, and then consult a doctor as soon as

possible.

• Discard the waste antifreeze liquid or used mixed soft water with antifreeze liquid as follows;

Absorb in a sawdust or waste cloth, then incinerate it.
Entrust to an industrial waste disposal contractor, clarifying their contents.

• Avoid causing ignition with static electricity, impact spark and so on.
• Be sure to wear goggles and gloves for handling the antifreeze liquid.

«
...
3
4
5
6
7
...
»

Содержание Kebab MKII

























































Отзывы:

Нет отзывов

Похожие инструкции для Kebab MKII

Бренд: Canon Страницы: 18

Бренд: Canon Страницы: 16

Бренд: Canon Страницы: 39

Бренд: Canon Страницы: 2

Бренд: Canon Страницы: 73

Бренд: Canon Страницы: 29

Бренд: Canon Страницы: 16

Бренд: Canon Страницы: 44

Бренд: Canon Страницы: 60

Бренд: Olympus Страницы: 236

I450 - i 450 Color Inkjet Printer

Бренд: Canon Страницы: 13

Бренд: QMS Страницы: 86

Бренд: Samsung Страницы: 2

Бренд: TallyGenicom Страницы: 175

M-Class Mark II M-4206

Бренд: Datamax Страницы: 22

Бренд: DataCard Страницы: 7

VarioPrint 6000 MICR series

Бренд: Oce Страницы: 264

Бренд: Oce Страницы: 194

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды