MIMAKI JV400-130SUV, Руководство по эксплуатации

Страница: 155 / 194

Warning / Error Messages
5-13
1
1
1
1
5
T
roubleshooting
Message Cause Solution
The data has been received.
• Press the key to perform print-
ing. Or, perform data clear.
The value of the negative pressure sen-
sor is abnormal.
• Perform “PRESSURE ADJUST ( P.5-9)”
of the maintenance. If you cannot adjust it
to the normal value, or, even if you perform,
it may be displayed, contact your local dis-
tributor to call for service.
The value of the positive pressure sen-
sor is abnormal.
The ink of the ink cartridge has been
nearly used up.
• Press the key to check the rele-
vant cartridge. Be careful because it may
be INK NEAR END soon.
Ink could not be supplied to the sub
tank.
• Perform “SUB TANK ( P.5-8) ” of the
maintenance. Also check the remaining
amount of ink in the cartridge.
Even if you performed this, when the mes-
sage is displayed, contact your local distrib-
utor to call for service.
The liquid level sensor abnormality of
the sub tank has been detected.
• Turn off the power to the machine and turn
it on after a while.
If the same error message appears again,
contact your local distributor to call for ser-
vice.
Overflow from the sub tank has been
detected.
• Perform “SUB TANK ( P.5-8) ” of the
maintenance. Also check the remaining
amount of ink in the cartridge.
Even if you performed this, when the mes-
sage is displayed, contact your local distrib-
utor to call for service.
Though a certain amount was con-
sumed, there is no change in the sub
tank sensor High.
Though a certain amount was con-
sumed, there is no change in the sub
tank sensor Low.
The machine temperature is high.
• Adjust the ambient temperature of the
installation place.
The machine temperature is low.
It is time to replace the UV lamp.
• Perform “UV CURING CHECK ( P.4-
41)” of maintenance, and check the illumi-
nance.
• When ink is not sufficiently cured, contact
your local distributor to call for service.
UV lamp shading cover is opened. • Close the cover.
After “error 710 HEATER TEMP
ERROR” has occurred, the power is
forcibly turned off, and when you restart
it, this is displayed.
• If the ERROR 710 appears again, contact
your local distributor to call for service.
The specified expiration date of an ink
cartridge has passed.
• The expiration date has passed.
• However, you can use it until the end of the
following month.
• Press the key to check the car-
tridge generating the warning.
The expiration date of an ink cartridge
has passed (one month has passed
after the specified expiration date).
• One month has passed after the expiration
date. However, you can use it until the end
of this month. (The red LED blinks.)
• Press the key to check the car-
tridge generating the warning.
< L OC A L >
D A T A R EMA I N
< L OC A L >
N EGA T I V E P R E S S U R E
< L OC A L >
POS I T I V E P R E S S U R E
< L OC A L >
I N K N E A R E ND [ E N T ]
< L OC A L >
S U P P L Y I N K : MMC C Y Y K K
< L OC A L >
S u b t a n k S e n s : MMC C Y Y K K
< L OC A L >
I n k O v e r f l o w : MMC C Y Y K K
< L OC A L >
T A N K l e v r l H : MMC C Y Y K K
< L OC A L >
T A N K l e v r l L
: MMC C Y Y K K
< L OC A L >
M a c h i n e T EMP / H i * * *
°
C
< L OC A L >
M a c h i n e T EMP / L o * * *
°
C
< L OC A L >
U V CU R I NG CH E C K
< L OC A L >
U V L AMP COV E R
H E A T E R T EMP E RROR
POWE R O F F
[ Ε N T ]
< L OC A L >
E x p i r a t i o n
[ E N T ]
< L OC A L >
E x p i r a t i o n ( 1 M )
[ E N T ]