Meridian Link/Customer Controlled Routing Скачать руководство пользователя страница 60 | Manualshive

Страница: 60 / 595

background image

42

Chapter 4: Meridian Link/CCR hardware

553-3202-210 Standard October 1998

Connector panel and I/O connectors (Option 11)

Underneath each cabinet of the Option 11 is a connector panel with ten
numbered connector ports. Each connector port connects to the
corresponding numbered slot directly above it, inside the cabinet. Figure 8
shows the connector panel for the main cabinet, and Figure 9 shows the
connector panel for the expansion cabinet.

The I/O connectors for the IPE Module installed in an Option 11 system are
standard, shielded, 50-pin tip-ring-type connector ports on the connector
panel, which is located under the cabinet containing the module. The
connector ports used depend on the slots occupied by the IPE Module.
Tables 5 and 6 show the connector ports used for each possible location of
the IPE Module. Figure 6 shows the IPE Module installed in slots 5, 6, and
7 of an Option 11 main cabinet. Table 5 shows that the cables are connected
to connector ports J5 and J7.

Figure 8
Option 11 connector panel (main cabinet)

0

1

2

3

4

5

6

7

8

9

¥

Table 5
Option 11 IPE Module connectors used (main cabinet)

Slots occupied by IPE Module

Connector ports used

2, 3, 4

J2 and J4

3, 4, 5

J3 and J5

4, 5, 6

J4 and J6

5, 6, 7

J5 and J7

6, 7, 8

J6 and J8

7, 8, 9

J7 and J9

«
...
58
59
60
61
62
...
»

Содержание Link/Customer Controlled Routing




















































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Link/Customer Controlled Routing

Бренд: Eaton Страницы: 10

Бренд: Alcad Страницы: 6

Бренд: Parker Страницы: 50

Бренд: Hama Страницы: 6

UniFi Cloud Key

Бренд: Ubiquiti Страницы: 13

Oresund EFC102200

Бренд: Bridgeworks Страницы: 84

Бренд: Cisco MERAKI Страницы: 4

Бренд: Medel Страницы: 28

Бренд: MSNswitch Страницы: 2

Бренд: Lanpro Страницы: 3

Бренд: Lefroy Brooks Страницы: 10

ExpressCard 11-in-1 Reader/Writer

Бренд: SIIG Страницы: 8

Meridian 1 Option 11C Mini

Бренд: Meridian Страницы: 546

IPSec VPN Client Zyxel ZyWall 10

Бренд: TheGreenBow Страницы: 12

Бренд: Datel Страницы: 8

Бренд: AMD Страницы: 10

Бренд: Adeunis RF Страницы: 9

Бренд: protech Страницы: 110

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды