Meridian Link/Customer Controlled Routing Скачать руководство пользователя страница 169 | Manualshive

Страница: 169 / 595

background image

151

Meridian Link Release 5C/CCR Release 3C Installation and Upgrade Guide

Chapter 9: Meridian Link/CCR interface
cabling

The cable requirements for the IPE Module and the Application Module are
completely different. For example, the Application Module uses power
harness cables, but IPE Modules receive power from the IPE backplane and
have no power cabling.

This chapter describes cabling required for the IPE Module and the
Application Module, and also provides procedures for connecting the
IPE Module and Application Module to external equipment.

IPE Module cabling

The IPE Module has two types of cable:

¥

IPE Module cables

¥

external cables (connect the IPE Module cables to the Meridian 1
system, the system console, the host computer, and Meridian Mail as
required)

IPE Module cables

IPE Module cables connect the connector ports on the connector panel (for
an Option 11 system) or on an I/O panel (for an Options 21Ð81 system) to
the external cables. IPE Module cables also provide port connectors for the
IPE Module. Figure 42 shows an illustration of the IPE Module octopus
cables NT1R03AA and NT1R03BA. Table 41 lists the IPE Module cables.
The Option 11 IPE Module requires extension cables to connect the
recessed connector panel to the IPE Module octopus cables.

«
...
167
168
169
170
171
...
»

Содержание Link/Customer Controlled Routing




















































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Link/Customer Controlled Routing

Device Server UDS 10

Бренд: Lantronix Страницы: 8

Бренд: hilscher Страницы: 154

Бренд: Avolites Страницы: 24

Бренд: ZyXEL Communications Страницы: 485

BIC 1I12-P2A25-M30MI1-BPX05-110

Бренд: Balluff Страницы: 12

Бренд: IBM Страницы: 34

PowerBeam PBE-5AC-400-ISO

Бренд: Ubiquiti Страницы: 23

Бренд: Rolls Страницы: 1

Бренд: Ubiquiti Страницы: 28

NetCon FBR-1409TX

Бренд: LevelOne Страницы: 88

Бренд: Navitar Страницы: 1

Бренд: ALIBI Страницы: 232

Бренд: Billion Страницы: 158

Бренд: Z3 Technology Страницы: 83

Бренд: Patton electronics Страницы: 8

Бренд: PairGain Страницы: 76

Бренд: Aztech Страницы: 13

ibaPADU-S-IT-16

Бренд: IBA Страницы: 80

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды