Meridian Link/Customer Controlled Routing Скачать руководство пользователя страница 395 | Manualshive

Страница: 395 / 595

Meridian Link/Customer Controlled Routing Скачать руководство пользователя страница 395

Chapter 14: Software installation, upgrade, and update procedures

377

Meridian Link Release 5C/CCR Release 3C Installation and Upgrade Guide

Section 2: To upgrade Meridian Link from Release 3 to
Release 5C or Co-residency using a Release 3 backup tape

If you already have Meridian Link Release 3 and want to upgrade to
Meridian Link Release 5C or Co-residency:

¥

Ensure that your backup is current so that you will not lose any
configuration and data information when you format the hard disk.

¥

Install the operating system and all applications.

¥

Enter a keycode to activate the appropriate application or applications.

To do this,

¥

Perform Procedure 11: Back up configuration and data files.

Note:

At this point, Release 3 is still installed. Procedure 11, although

intended for Release 5C, can be used to back up Release 3 files. Ignore
any differences between the messages shown in Procedure 11 and the
messages you see.

¥

Perform Procedure 4: Power down the IPE Module or the Application
Module.

¥

Depending on the type of SBC card installed, perform one of the
following:

Ñ Procedure 5: Load the operating system on an Application Module

with an MVME147 card

Ñ Procedure 6: Load the operating system tape on an IPE Module or

an Application Module with an MVME167 card

¥

Perform Procedure 7: Reboot and go through setup.

¥

Perform Procedure 8: Load the application software from tape.

¥

Perform Procedure 9: Restore configuration files and data files from the
backup tape to customize your system

¥

Perform Procedure 10: Verify the installation to confirm that the
installation is complete and correct

¥

Perform Procedure 11: Back up configuration files and data files to
back up the customized new release

«
...
393
394
395
396
397
...
»

Содержание Link/Customer Controlled Routing




















































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды