Meridian Link/Customer Controlled Routing Скачать руководство пользователя страница 305

Страница: 305 / 595

Chapter 11: Peripheral device cabling interface

287

Meridian Link Release 5C/CCR Release 3C Installation and Upgrade Guide

Connect the modem directly to the IPE Module or Application
Module, as described in Chapter 9, ÒMeridian Link/CCR interface
cabling.Ó

If the modem installation is successful, the LED labelled ÒTRÓ on the
front panel of the modem lights up.

The following procedure explains how to configure the UDS 2440 modem
using a workstation.

Connect the modem to a workstation and apply power to both.

Enter each entry shown under the ÒInputÓ column in Table 104 and
press [Enter]. The system response to each entry should be ÒOK.Ó

Table 104
UDS 2440 modem configuration (workstation)

Input

System response

atz

at&f

ats0=1

at&d3

at&s1

at&c1

at&w

Power down the workstation and the modem.

Disconnect the modem from the workstation.

Connect the modem to the IPE Module using an NT1R03HF cable,
or to an Application Module using an NT7D99AA cable.

If the modem installation is successful, the LED labelled ÒTRÓ on the
front panel of the modem lights up.

Содержание Link/Customer Controlled Routing




















































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Link/Customer Controlled Routing

Отзывы:

Похожие инструкции для Link/Customer Controlled Routing

Бренды по названию

Популярные бренды

Meridian Link/Customer Controlled Routing, Руководство по установке и обновлению

Результаты поиска

Содержание Link/Customer Controlled Routing

Отзывы:

Похожие инструкции для Link/Customer Controlled Routing

Бренды по названию

Популярные бренды