Meridian Link/Customer Controlled Routing Скачать руководство пользователя страница 464 | Manualshive

Страница: 464 / 595

Meridian Link/Customer Controlled Routing Скачать руководство пользователя страница 464

446

Chapter 14: Software installation, upgrade, and update procedures

553-3202-210 Standard October 1998

Procedure 6: Load the operating system tape on an IPE Module or an
Application Module with an MVME167 card (continued)

Figure 200
BOS installation, phases 3 and 4

***> Checking tape in drive

Phase 3. Prepare Installation Disk Drive(s)

***> Retensioning tape (in background)
***> Formatting root file systemÕs disk drive
***> Writing slice table to /dev/rdsk/m167_00s7
***> Creating the root file system
***> Labeling the root file system
***> Creating the usr file system
***> Labeling the usr file system
***> Installing boot-loader on root file systemÕs disk drive
***> Mounting root file system as /root
***> Making the /tmp directory
***> Making the /usr directory
***> Mounting usr file system as /root/usr

Phase 4. Install BOS Software

***> Waiting for tape to complete retensioning
***> Copying files; this will take from 10-35 minutes
depending upon your system configuration...
70240 blocks
1200 blocks
10960 blocks
***> Making the root file system lost+found directory

Reserving 160 entries
***> Making the usr file system lost+found directory

Reserving 960 entries
***> Installing /etc/badtracks/m167_00 bad spot list
***> Creating sysadm(1M) package information file
***> Setting up the new operating system
***> Creating root and usr file system associated device nodes
***> Setting permissions on installation diskÕs root directory
***> Running mkcomply to confirm correct installation
***> Setting rootÕs password entry
New password:

29

At the ÒNew password:Ó prompt, press [Return].

The system responds with ÒRe-enter new password:Ó

30

Press [Return] again.

«
...
462
463
464
465
466
...
»

Содержание Link/Customer Controlled Routing




















































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды