Meridian Link/Customer Controlled Routing Скачать руководство пользователя страница 52 | Manualshive

Страница: 52 / 595

Meridian Link/Customer Controlled Routing Скачать руководство пользователя страница 52

34

Chapter 3: Overview of Customer Controlled Routing

553-3202-210 Standard October 1998

Meridian 1

This section provides overviews of the Meridian 1 hardware and software
required for CCR.

Hardware overview

One of the following system types must be installed and operational:

¥

Meridian 1 system options 21, 51, 61, 71, or 81 (not all system options
are supported in all markets)

¥

Meridian 1 system option 11

¥

Meridian SL-1 systems (upgraded) capable of operating on generic X11
Release 17, or later, software

The Meridian 1 system must be up and running, and have the following
hardware installed:

¥

one of the following interface cards:

Ñ QPC513 Enhanced Serial Data Interface (ESDI) card (vintage G or

later)

Ñ NT6D80 Multi-purpose Serial Data Link (MSDL) card

Ñ (Option 11 only) NTAK02AB Serial Data Interface/D-Channel

Interface (SDI/DCH) card

¥

a Serial Data Interface (SDI) card if conshare capability is desired

Note:

Conshare capability, which gives you access to MeridianÊ1

input/output programs from the IPE Module or Application Module
console, is highly recommended to allow for more effective support for
your system. If you want to access Meridian 1 and up to three other
applications, the Single Terminal Access (STA) feature is available
with X11 release 19 and greater. For more information on STA, refer to
Chapter 19, ÒSingle Terminal Access.Ó

«
...
50
51
52
53
54
...
»

Содержание Link/Customer Controlled Routing




















































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды