Mercury Racing HP525 EFI Bravo Sterndrive Series Скачать руководство пользователя страница 116

Страница: 116 / 147

MAINTENANCE

106

eng

1. Remove the water separating fuel filter and sealing ring from

mounting bracket and discard.

a -

Water separating fuel filter

b -

Sealing ring

c -

Mounting bracket

2. Coat the sealing ring on new filter with motor oil.

IMPORTANT: Do not use a filter wrench to tighten the filter.

3. Thread the filter onto the bracket and tighten securely by

hand.

4. Start and run engine. If the engine stops or will not start, it

may be necessary to prime the fuel system (see

Priming the

Fuel System Prior to Starting

in the

Cold Weather or

Extended Storage

section of this manual).

5. Check the filter connection for fuel leaks. If leaks exist,

recheck the filter installation.

6. If leaks continue, stop the engine immediately and contact

your authorized Mercury MerCruiser dealer.

6152

Содержание HP525 EFI Bravo Sterndrive Series




















































































































































Результаты поиска

Содержание HP525 EFI Bravo Sterndrive Series

Отзывы:

Похожие инструкции для HP525 EFI Bravo Sterndrive Series

Бренды по названию

Популярные бренды

Mercury Racing HP525 EFI Bravo Sterndrive Series, Инструкция по эксплуатации, техническому обслуживанию и гарантии

Результаты поиска

Содержание HP525 EFI Bravo Sterndrive Series

Отзывы:

Похожие инструкции для HP525 EFI Bravo Sterndrive Series

Бренды по названию

Популярные бренды