Mercury Racing HP525 EFI Bravo Sterndrive Series Скачать руководство пользователя страница 36

Страница: 36 / 147

GENERAL INFORMATION

eng

Make sure everyone in the boat is properly seated. Do not allow

anyone to sit or ride on any part of the boat that was not

intended for such use. This includes the back of seats,

gunwales, transom, bow, decks, raised fishing seats, any

rotating fishing seat; or anywhere that an unexpected

acceleration, sudden stopping, unexpected loss of boat control,

or sudden boat movement could cause a person to be thrown

overboard or into the boat.
Never be under the influence of alcohol or drugs while boating (it

is the law). Alcohol or drug use impairs your judgment and

greatly reduces your ability to react quickly.

Know your boating area and avoid hazardous locations.

Prepare other boat operators. Instruct at least one other person

on board in the basics of starting and operating the power

package, and boat handling, in case the driver becomes disabled

or falls overboard.
Passenger boarding. Stop the engine whenever passengers are

boarding, unloading, or are near the back (stern) of the boat.

Just shifting the power package into neutral is not sufficient.
Be alert. The operator of the boat is responsible by law to

maintain a proper lookout by sight and hearing. The operator

must have an unobstructed view particularly to the front. No

passengers, load, or fishing seats should block the operators

view when operating the boat above idle speed.
Never drive your boat directly behind a water skier in case the

skier falls. As an example, your boat traveling at 40 km/h

(25 MPH) will overtake a fallen skier 61 m (200 ft.) in front of you

in five seconds.
Watch fallen skiers. When using your boat for water skiing or

similar activities, always keep a fallen or down skier on the

operator's side of the boat while returning to assist the skier. The

operator should always have the down skier in sight and never

back up to the skier or anyone in the water.
Report accidents. Boat operators are required by law to file a

boating accident report with their state boating law enforcement

agency when their boat is involved in certain boating accidents.

A boating accident must be reported if:

Содержание HP525 EFI Bravo Sterndrive Series




















































































































































Результаты поиска

Содержание HP525 EFI Bravo Sterndrive Series

Отзывы:

Похожие инструкции для HP525 EFI Bravo Sterndrive Series

Бренды по названию

Популярные бренды

Mercury Racing HP525 EFI Bravo Sterndrive Series, Инструкция по эксплуатации, техническому обслуживанию и гарантии

Результаты поиска

Содержание HP525 EFI Bravo Sterndrive Series

Отзывы:

Похожие инструкции для HP525 EFI Bravo Sterndrive Series

Бренды по названию

Популярные бренды