Mercury Racing HP525 EFI Bravo Sterndrive Series Скачать руководство пользователя страница 109

Страница: 109 / 147

MAINTENANCE

eng

19310

SportMaster Low Water Pickup

NOTE: Flushing is needed only for salty, brackish, mineral laden

or polluted water applications. Flushing is recommended after

each outing.

NOTICE

Flushing the engine with the boat in the water can cause

seawater to flow into the engine, resulting in engine damage.

Close the seacock before flushing the engine. Keep the

seacock closed until starting the engine.

1. Drain the seawater section of the cooling system.
2. If flushing the cooling system with the boat in the water:

a. Raise sterndrive unit to trailer position.
b. Install the appropriate flushing attachment over the water

inlet holes in the gear housing.

c. Lower sterndrive unit to full down/in position.

Содержание HP525 EFI Bravo Sterndrive Series




















































































































































Результаты поиска

Содержание HP525 EFI Bravo Sterndrive Series

Отзывы:

Mercury Racing HP525 EFI Bravo Sterndrive Series, Инструкция по эксплуатации, техническому обслуживанию и гарантии, Страница: 109 / 147

Результаты поиска

Содержание HP525 EFI Bravo Sterndrive Series

Отзывы: