Mercury Racing HP525 EFI Bravo Sterndrive Series Скачать руководство пользователя страница 8

Страница: 8 / 147

viii

eng

Troubleshooting

Engine Will Not Crank..............................................................126

Engine Cranks But Will Not Start............................................. 126

Engine Hard to Start, Runs Rough, Misses, and/or Backfires. 127

Low Engine Coolant (Closed Cooling) Temperature............... 127

Poor Performance....................................................................128

Insufficient Engine Temperature.............................................. 128

High Engine Temperature........................................................129

Low Engine Oil Pressure......................................................... 129

Battery Will Not Come Up On Charge..................................... 130

Power Trim Does Not Operate (Motor Doesn't Run)............... 130

Power Trim Does Not Operate (Motor Runs But Drive Unit Does

Not Move)................................................................................ 130

Electrical Analog Trim Gauge Malfunction...............................131

Remote Control Operates Hard, Binds, Has Excessive Free‑Play

or Makes Unusual Sounds.......................................................131

Steering Wheel Turns Hard or Jerky....................................... 131

Seawater Pressure Is Below Specification.............................. 132

Seawater Pressure Is Above Specification.............................. 132

Owner Service Assistance

Local Repair Service................................................................133

Service Away from Home........................................................ 133

Parts and Accessories Inquiries.............................................. 133

Service Assistance.................................................................. 133

Mercury Mercruiser Service Offices.........................................134

Ordering Literature

United States and Canada.......................................................136

Outside The United States and Canada.................................. 136

Содержание HP525 EFI Bravo Sterndrive Series




















































































































































Результаты поиска

Содержание HP525 EFI Bravo Sterndrive Series

Отзывы:

Mercury Racing HP525 EFI Bravo Sterndrive Series, Инструкция по эксплуатации, техническому обслуживанию и гарантии, Страница: 8 / 147

Результаты поиска

Содержание HP525 EFI Bravo Sterndrive Series

Отзывы: