Mercury Racing HP525 EFI Bravo Sterndrive Series Скачать руководство пользователя страница 45

Страница: 45 / 147

SPECIFICATIONS

eng

Engine Break‑in

IMPORTANT: Failure to follow the engine break‑in procedures

can result in poor performance throughout the life of the engine

and can cause engine damage. Always follow break‑in

procedures.

5 Hr. Break‑in Procedure

•

Allow engine to warm‑up for 30‑60 seconds.

•

Do not exceed 3/4 throttle.

•

Avoid full throttle acceleration from idle speed.

•

Always vary throttle setting.

•

Run engine the majority of time between 3000 ‑ 4500 RPM.

•

Frequently check engine oil level. Add oil if needed. It is normal for oil

consumption to be high during break‑in period.

After Break‑In Period

To help extend the life of your power package, Mercury Marine

recommends the following:

After 5 hr. Break‑in

•

Use a propeller that allows the engine to operate at or near the top of the

maximum RPM range (See

Specifications

section) when at full throttle

with a normal boat load.

•

Do not advance the throttle until the engine runs smoothly at idle and

water temperature reaches a minimum of 54 °C (130 °F). Do not operate

at full throttle until the engine oil temperature reaches 60 °C (140 °F).

•

Follow the maintenance schedule in this manual.

Содержание HP525 EFI Bravo Sterndrive Series




















































































































































Результаты поиска

Содержание HP525 EFI Bravo Sterndrive Series

Отзывы:

Похожие инструкции для HP525 EFI Bravo Sterndrive Series

Бренды по названию

Популярные бренды

Mercury Racing HP525 EFI Bravo Sterndrive Series, Инструкция по эксплуатации, техническому обслуживанию и гарантии

Результаты поиска

Содержание HP525 EFI Bravo Sterndrive Series

Отзывы:

Похожие инструкции для HP525 EFI Bravo Sterndrive Series

Бренды по названию

Популярные бренды