Mercury Racing HP525 EFI Bravo Sterndrive Series Скачать руководство пользователя страница 84

Страница: 84 / 147

MAINTENANCE

eng

Changing Fluids

See the

Maintenance Chart

for lubricant change frequency.

Lubricant should be changed before placing the boat in storage.
Power trim or power steering fluids do not require changing.

CRANKCASE OIL AND FILTER (BOAT IN THE WATER)

IMPORTANT: Change oil when engine is warm from operation.

Warm oil flows more freely, carrying away more impurities. Use

only recommended motor oil (see

Specifications

1. With the engine at normal operating temperature, remove

the dipstick.

2. Install the crankcase oil pump onto the dipstick tube.
3. Insert the hose end of crankcase oil pump into an

appropriate container and, using the pump handle, pump

until the crankcase is empty.

a -

Crankcase oil pump

b -

Crankcase oil pump hose

4. Remove the crankcase oil pump.
5. Place a container below the oil filter.

NOTE: To allow the oil to drain from the filter, loosen the filter

just enough to break the internal vacuum. Let the oil drain back

into the system for 15 minutes prior to complete removal of the

filter.

a -

Crankcase oil filter

6. Remove the oil filter from the adaptor and discard the old oil

filter and old sealing ring.

7983

7984

Содержание HP525 EFI Bravo Sterndrive Series




















































































































































Результаты поиска

Содержание HP525 EFI Bravo Sterndrive Series

Отзывы:

Похожие инструкции для HP525 EFI Bravo Sterndrive Series

Бренды по названию

Популярные бренды

Mercury Racing HP525 EFI Bravo Sterndrive Series, Инструкция по эксплуатации, техническому обслуживанию и гарантии

Результаты поиска

Содержание HP525 EFI Bravo Sterndrive Series

Отзывы:

Похожие инструкции для HP525 EFI Bravo Sterndrive Series

Бренды по названию

Популярные бренды