Mercury Racing HP525 EFI Bravo Sterndrive Series Скачать руководство пользователя страница 112

Страница: 112 / 147

MAINTENANCE

102

eng

3. Flush passages with fresh water.
4. Inspect gaskets for deterioration and replace if necessary.
5. Install gaskets and end plates. Tighten screws securely.

POWER STEERING COOLER
NOTE: The power steering cooler is located on the lower port

side of the engine.

1. Loosen water hose clamps and remove hoses if it is

necessary to inspect or clean cooler.

IMPORTANT: If the oil hoses need to be removed from the

cooler, be prepared to cap or plug them to avoid draining the

power steering reservoir.

a -

Hose clamps (2)

2. Re‑install cooler and tighten hose clamps securely.
3. Check power steering fluid level.
4. Start engine and inspect cooling system for leaks.

Changing Positive Crankcase Ventilation Valve

This engine is equipped with a positive crankcase ventilation

valve (PCV). Change the valve every 150 hours of operation.

• Pull valve out of intake manifold and remove valve from

hose.

8031

Содержание HP525 EFI Bravo Sterndrive Series




















































































































































Результаты поиска

Содержание HP525 EFI Bravo Sterndrive Series

Отзывы:

Похожие инструкции для HP525 EFI Bravo Sterndrive Series

Бренды по названию

Популярные бренды

Mercury Racing HP525 EFI Bravo Sterndrive Series, Инструкция по эксплуатации, техническому обслуживанию и гарантии

Результаты поиска

Содержание HP525 EFI Bravo Sterndrive Series

Отзывы:

Похожие инструкции для HP525 EFI Bravo Sterndrive Series

Бренды по названию

Популярные бренды