Mercury Racing HP525 EFI Bravo Sterndrive Series Скачать руководство пользователя страница 24

Страница: 24 / 147

GENERAL INFORMATION

eng

Before Operating Your Boat

Read this manual carefully. Safety and operating information that

is practiced along with using good common sense can help

prevent personal injury and product damage. If you have any

questions, contact your dealer.
This manual as well as safety labels posted on the engine

package use safety alerts to draw your attention to special safety

instructions that must be followed.

WARNING

Indicates a hazardous situation which, if not avoided, could

result in death or serious injury.

CAUTION

Indicates a hazardous situation which, if not avoided, could

result in minor or moderate injury.

IMPORTANT: Indicates information or instructions that are

necessary for proper operation and/or maintenance.

NOTE: Indicates information that helps in the understanding of a

step or action.

Boat Horsepower Capacity

WARNING

Exceeding the boat's maximum horsepower rating can cause

serious injury or death. Overpowering the boat can affect boat

control and flotation characteristics or break the transom. Do

not install an engine that exceeds the boat's maximum power

rating.

Содержание HP525 EFI Bravo Sterndrive Series




















































































































































Результаты поиска

Содержание HP525 EFI Bravo Sterndrive Series

Отзывы:

Похожие инструкции для HP525 EFI Bravo Sterndrive Series

Бренды по названию

Популярные бренды

Mercury Racing HP525 EFI Bravo Sterndrive Series, Инструкция по эксплуатации, техническому обслуживанию и гарантии

Результаты поиска

Содержание HP525 EFI Bravo Sterndrive Series

Отзывы:

Похожие инструкции для HP525 EFI Bravo Sterndrive Series

Бренды по названию

Популярные бренды