Mercury Racing HP525 EFI Bravo Sterndrive Series Скачать руководство пользователя страница 96

Страница: 96 / 147

MAINTENANCE

eng

DRIVE UNIT AND TRANSOM ASSEMBLY

IMPORTANT: Disconnect the speedometer hose fitting from the

driveshaft housing prior to removing the sterndrive unit to

prevent damage to the fitting.

IMPORTANT: Sterndrive must be removed to lubricate U‑joints.

Contact your authorized Mercury MerCruiser dealer for this

service.

NOTE: The engine coupling and shaft splines are greased with

engine coupler spline grease. Universal joints are greased with

2‑4‑C with PTFE lubricant. Contact your authorized Mercury

MerCruiser dealer for this service.

1. Lubricate gimbal bearing with 2‑4‑C with PTFE lubricant.

a -

Gimbal bearing

grease fitting

Tube

Ref No.

Description

Where Used

Part No.

2-4-C Marine

Lubricant with

PTFE

Gimbal bearing

92-802859A 1

mc77068-1

Содержание HP525 EFI Bravo Sterndrive Series




















































































































































Результаты поиска

Содержание HP525 EFI Bravo Sterndrive Series

Отзывы:

Mercury Racing HP525 EFI Bravo Sterndrive Series, Инструкция по эксплуатации, техническому обслуживанию и гарантии, Страница: 96 / 147

Результаты поиска

Содержание HP525 EFI Bravo Sterndrive Series

Отзывы: