Mercury Racing HP525 EFI Bravo Sterndrive Series Скачать руководство пользователя страница 127

Страница: 127 / 147

COLD WEATHER OR EXTENDED STORAGE

eng

117

Power Package Lay‑up

IMPORTANT: This service should be performed by an

authorized Mercury MerCruiser dealer.

NOTICE

Without sufficient cooling water, the engine, the water pump,

and other components will overheat and suffer damage.

Provide a sufficient supply of water to the water inlets during

operation.

IMPORTANT: Before starting the engine, attach a water source

to the seawater pickup pump. Follow all warnings and flushing

attachment procedures stated in the

Flushing Cooling System

section of this manual.

1. Run engine sufficiently to bring it up to normal operating

temperature. Shut off engine and change oil and oil filter.

2. Flush cooling system. Refer to

Flushing Cooling System

shown earlier in this manual.

WARNING

Fuel vapors trapped in the engine compartment may be an

irritant, cause difficulty breathing, or may ignite resulting in a

fire or explosion. Always ventilate the engine compartment

before servicing the power package.

3. Close the fuel shut off valve if equipped.
4. Prepare fuel system for extended storage by mixing the

following in a 23 liter (6 U.S. gal) remote outboard fuel tank:

• 19 liter (5 U.S. gal) regular unleaded 87 octane (R+M)/2

(92 RON) gasoline.

• 1.89 liter (64 fl oz) Premium Plus 2‑cycle TC‑W3

outboard oil.

• 150 ml (5 fl oz) Fuel System Treatment and Stabilizer or

30 ml (1 fl oz) Fuel System Treatment and Stabilizer

Concentrate.

5. Disconnect and plug the boat's fuel line from the water

separating fuel filter inlet.

Содержание HP525 EFI Bravo Sterndrive Series




















































































































































Результаты поиска

Содержание HP525 EFI Bravo Sterndrive Series

Отзывы:

Похожие инструкции для HP525 EFI Bravo Sterndrive Series

Бренды по названию

Популярные бренды

Mercury Racing HP525 EFI Bravo Sterndrive Series, Инструкция по эксплуатации, техническому обслуживанию и гарантии

Результаты поиска

Содержание HP525 EFI Bravo Sterndrive Series

Отзывы:

Похожие инструкции для HP525 EFI Bravo Sterndrive Series

Бренды по названию

Популярные бренды