Meatest M133C Скачать руководство пользователя страница 95

Страница: 95 / 148

M133C Electric Power/Energy Calibrator

MEATEST

Operation manual

Example:
Voltage 230.5V in channel 1:

PHAR:VOLT1 230.5

Note:
Command switches the calibrator in Power Harmonic mode.

[SOUR]:PHAR:VOLT<n>:PHAS(?) <DNPD>

This command sets the phase angle between voltage output in channel <n> and internal reference
phase.

<DNPD>
Represents the phase angle in degrees.

If query is sent, calibrator returns the set value of the phase angle using standard exponential
format. Example: 156.3



is returned as 1.002.

Example:
PHAR:VOLT1:PHAS 0
PHAR:VOLT2:PHAS 120
PHAR:VOLT3:PHAS 240

Note:
Command switches the calibrator in Power Harmonic mode.

[SOUR]:PHAR:VOLT<n>:ENAB(?) <CPD> { ON | OFF }

This command enables (disables) the voltage output in channel <n>. Disabled outputs are OFF
also during OUTP ON.



ON - enables the output



OFF - disables the output

If query is sent, calibrator returns ON if the output is enabled or OFF if it is disabled.

Example:
PHAR:VOLT1:ENAB ON

Note:
Command switches the calibrator in Power Harmonic mode.

[SOUR]:PHAR:VOLT<n>:HARM<y>(?) <DNPD>

This command sets the level of <y> harmonic in output voltage in channel <n>

<DNPD>
Parameter represents the level of <y> harmonic expressed in %.

<n>
Parameter represents the output channel (1, 2 or 3).

Содержание M133C





















































































































































Результаты поиска

Содержание M133C

Отзывы:

Бренды по названию

Популярные бренды

Meatest M133C, Руководство по эксплуатации

Результаты поиска

Содержание M133C

Отзывы:

Бренды по названию

Популярные бренды