McDATA Enterprise Operating System Скачать руководство пользователя страница 302 | Manualshive

Страница: 302 / 328

background image

g-2

Enterprise Operating System Command Line Interface User Manual

Glossary

See

. This refers the reader to another keyword or phrase for the same

term.

See also

. This refers the reader to definite additional information

contained in another entry.

A

access control

A list of all devices that can access other devices across the network
and the permissions associated with that access.

See also

persistent

binding

;

zoning

.

active

field-replaceable unit

Active FRU. A FRU that is currently operating as the active, and not
the backup FRU.

See also

backup field-replaceable unit

.

active zone set

A single zone set that is active in a multiswitch fabric and is created
when a specific zone set is enabled. This zone set is compiled by
checking for undefined zones or aliases.

See also

zone

;

zone set

.

AL_PA

See

arbitrated loop physical address

.

arbitrated loop

physical address

AL_PA. A 1-byte value used in the arbitrated loop topology that
identifies loop ports (L_Ports). This value then becomes the last byte
of the address identified for each public L_Port on the loop.

B

backup

field-replaceable unit

Backup FRU. When an active FRU fails, an identical backup FRU
takes over operation automatically (failover) to maintain director or
switch and Fibre Channel link operation.

See also

active

field-replaceable unit

.

backup FRU

See

backup field-replaceable unit

.

beaconing

Use of light-emitting diodes (LEDs) on ports, port cards,
field-replaceable units (FRUs), and directors to aid in the
fault-isolation process. When enabled, active beaconing will cause
LEDs to flash in order for the user to locate field-replaceable units
(FRU’s), switches, or directors in cabinets or computer rooms.

«
...
300
301
302
303
304
...
»

Содержание Enterprise Operating System









































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Enterprise Operating System

Бренд: Yamaha Страницы: 37

Бренд: Xerox Страницы: 28

Бренд: ViewSonic Страницы: 2

Web-based Management Utility

Бренд: Supermicro Страницы: 64

D:Scribe Standalone

Бренд: Sonifex Страницы: 32

Бренд: FujiFilm Страницы: 21

Бренд: FujiFilm Страницы: 21

Бренд: GRASS VALLEY Страницы: 1

Бренд: Autodesk Страницы: 4

240B1-05A111-1301 - Revit Architecture 2010

Бренд: Autodesk Страницы: 14

6100BD - Phaser Color Laser Printer

Бренд: Xerox Страницы: 56

CORE - MIGRATION GUIDE 11-2009

Бренд: FARONICS Страницы: 32

DISKRESCUE 2009 - V1

Бренд: UNIBLUE Страницы: 26

Storage Manager

Бренд: NEC Страницы: 134

HXDU010EB - Story Station 1 TB External Hard...

Бренд: Samsung Страницы: 7

Powershot S2 IS - Powershot S2 IS 5MP Digital...

Бренд: Canon Страницы: 137

Бренд: TANDBERG Страницы: 19

Бренд: TANDBERG Страницы: 84

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды