McDATA Enterprise Operating System Скачать руководство пользователя страница 282

Страница: 282 / 328

A-42

Enterprise Operating System Command Line Interface User Manual

Message

Error 262: All Attached Members are in the Membership List

Description

All attached fabric members are already in the membership list.

Action

This action is redundant, all members are already in the list.

Message

Error 263: The SANtegrity Authentication feature key is not
installed

Description

The SANtegrity Authentication feature key is not installed.

Action

Install the SANtegrity Authentication feature key.

Message

Error 264: The Preferred Path feature key is not installed

Description

The preferred path feature key must be installed.

Action

Install the preferred path feature key.

Message

Error 265: Duplicate threshold alert name

Description

The desired name for the threshold alert is already in use.

Action

Use a different name for the threshold alert.

Message

Error 266: Attached members cannot be added while fabric is
building

Description

Attached members cannot be added while the fabric is building.

Action

The fabric is still building, wait a couple of seconds until it is
complete.

Message

Error 268: RADIUS key too long

Description

The desired RADIUS key is too long.

Action

Use a shorter RADIUS key.

Содержание Enterprise Operating System









































































































































































































































































































































Результаты поиска

Содержание Enterprise Operating System

Отзывы:

Похожие инструкции для Enterprise Operating System

Бренды по названию

Популярные бренды

McDATA Enterprise Operating System, Руководство пользователя

Результаты поиска

Содержание Enterprise Operating System

Отзывы:

Похожие инструкции для Enterprise Operating System

Бренды по названию

Популярные бренды