McDATA Enterprise Operating System Скачать руководство пользователя страница 220

Страница: 220 / 328

2-176

Enterprise Operating System Command Line Interface User Manual

show

Output Example

The output from the show.port.status command displays as follows.

Port State Type Attached WWN Beaconing Reason

---- ---------------- ----- ----------------------- --------- ------

0 Online fPort 10:00:80:00:11:22:33:44 Off

1 Online gPort 10:00:80:00:11:22:33:45 On

2 No Light fPort 10:00:80:00:11:22:33:55 On

3 Offline ePort 10:00:80:00:11:22:33:00 Off

4 Online gPort 10:00:80:00:11:22:33:57 Off

5 Port Failure fPort 10:00:80:00:11:22:33:46 Off

6 Link Reset gPort 10:00:80:00:11:22:33:63 Off

7 Segmented E_Port ePort 10:00:80:00:11:22:33:47 Off 02

8 Online ePort 10:00:80:00:11:22:33:88 Off

9 Offline fPort 10:00:80:00:11:22:33:49 Off

10 Inactive ePort 10:00:80:00:11:22:33:50 Off 26

11 Online fPort 10:00:80:00:11:22:33:53 Off

12 No Light fPort 10:00:80:00:11:22:33:56 Off

13 Online fPort 10:00:80:00:11:22:33:59 Off

14 Invalid Attachment fPort 10:00:80:00:11:22:33:64 Off 15

15 Online fPort 10:00:80:00:11:22:33:66 Off

02: Duplicate Domain ID(s)

03: Switch Speed Conflict

07: ISL connection not allowed on this port

Reason (cont.)

If the operational state is

Inactive

only the

following messages can be generated:

• 24: Inactive - RC 0
• 25: No Serial Number
• 26: Feature Not Enabled
• 27: Switch Speed Conflict

Содержание Enterprise Operating System









































































































































































































































































































































Результаты поиска

Содержание Enterprise Operating System

Отзывы:

Похожие инструкции для Enterprise Operating System

Бренды по названию

Популярные бренды

McDATA Enterprise Operating System, Руководство пользователя

Результаты поиска

Содержание Enterprise Operating System

Отзывы:

Похожие инструкции для Enterprise Operating System

Бренды по названию

Популярные бренды