McDATA Enterprise Operating System Скачать руководство пользователя страница 131

Страница: 131 / 328

CLI Commands

2-87

config

config.zoning.addWwnMem

Syntax

addWwnMem zoneName wwn

Purpose

This command adds a WWN zone member to the specified zone in
the work area.

NOTE:

A product can have at most 1024 zone members in its zones.

NOTE:

The ED-5000 supports a maximum of 512 zones.

Parameters

This command has two parameters.

Command Example

Root>

config zoning addWwnMem TheUltimateZone

10:00:00:00:C9:22:9B:64

config.zoning.addZone

Syntax

addZone zoneName

Purpose

This command adds a new (empty) zone to the zone set in the work
area.

NOTE:

Changes are not activated on the switch until the

config.zoning.activateZoneSet command is issued.

NOTE:

A zone set can have a maximum of 1024 zones.

NOTE:

A Switch or Director can have a maximum of 1024 zone members in

all of its zones, except for the ED-5000, which allows a maximum of 512
zones.

zoneName

Specifies the name of the zone.

wwn

The WWN of the member to be added to the
zone. The value of the WWN must be in
colon-delimited hexadecimal notation (for
example, AA:00:AA:00:AA:00:AA:00).

Содержание Enterprise Operating System









































































































































































































































































































































Результаты поиска

Содержание Enterprise Operating System

Отзывы:

Похожие инструкции для Enterprise Operating System

Бренды по названию

Популярные бренды

McDATA Enterprise Operating System, Руководство пользователя

Результаты поиска

Содержание Enterprise Operating System

Отзывы:

Похожие инструкции для Enterprise Operating System

Бренды по названию

Популярные бренды